71M6521DE-IMR/F Maxim Integrated Products, 71M6521DE-IMR/F Datasheet - Page 102
71M6521DE-IMR/F
Manufacturer Part Number
71M6521DE-IMR/F
Description
IC ENERGY METER 16K FLASH 68-QFN
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6521DE-IMRF.pdf
(107 pages)
Specifications of 71M6521DE-IMR/F
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 102 of 107
- Download datasheet (3Mb)
Power/Ground Pins:
Name
GNDA
GNDD
V3P3A
V3P3SYS
V3P3D
VBAT
V2P5
Analog Pins:
Name
IA, IB
VA, VB
V1
VREF
XIN
XOUT
Page: 102 of 107
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output
The circuit number denotes the equivalent circuit, as specified under “I/O Equivalent Circuits”.
Type
Type
O
O
P
P
P
P
P
O
I
I
I
I
Circui
t
Circui
t
13
12
10
--
--
--
--
6
6
7
9
8
Description
Analog ground: This pin should be connected directly to the ground plane.
Digital ground: This pin should be connected directly to the ground plane.
Analog power supply: A 3.3V power supply should be connected to this pin, must be
the same voltage as V3P3SYS.
System 3.3V supply. This pin should be connected to a 3.3V power supply.
Auxiliary voltage output of the chip, controlled by the internal 3.3V selection switch.
In mission mode, this pin is internally connected to V3P3SYS. In BROWNOUT
mode, it is internally connected to VBAT. This pin is high impedance in LCD and
sleep mode.
Battery backup power supply. A battery or super-capacitor is to be connected
between VBAT and GNDD. If no battery is used, connect VBAT to V3P3SYS.
Output of the internal 2.5 V regulator. A 0.1µF capacitor to GNDA should be
connected to this pin.
Description
Line Current Sense Inputs: These pins are voltage inputs to the internal A/D
converter. Typically, they are connected to the outputs of current sensors. Unused
pins must be connected to V3P3A.
Line Voltage Sense Inputs: These pins are voltage inputs to the internal A/D
converter. Typically, they are connected to the outputs of resistor dividers. Unused
pins must be connected to V3P3A or tied to the voltage sense input that is in
use.
Comparator Input: This pin is a voltage input to the internal power-fail comparator.
The input voltage is compared to the internal BIAS voltage (1.6 V). If the input
voltage is above VBIAS, the comparator output will be high (1). If the comparator
output is lower, a voltage fault will occur and the chip will be forced to battery mode.
Voltage Reference for the ADC. This pin is normally disabled by setting the
VREF_CAL bit in the I/O RAM and can then be left unconnected. If enabled, a 0.1µF
capacitor to GNDA should be connected.
Crystal Inputs: A 32kHz crystal should be connected across these pins. Typically, a
27pF capacitor is also connected from each pin to GNDA. It is important to minimize
the capacitance between these pins. See the crystal manufacturer datasheet for
details.
PIN DESCRIPTIONS
71M6521DE/DH/FE Data Sheet
Rev 2
Related parts for 71M6521DE-IMR/F
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC ENERGY METER 16K FLASH 68-QFN
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC ENERGY METER 16K FLASH 64LQFP
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC ENERGY METER 16K FLASH 64LQFP
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Power Management Modules & Development Tools 71M6521DE DEMO BOARD M6521DE DEMO BOARD
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products