71M6511-IGTR/F Maxim Integrated Products, 71M6511-IGTR/F Datasheet - Page 94

• Manufacturer Part Number: 71M6511-IGTR/F
• Description: IC ENERGY METER RESIDENT 64-LQFP
• Manufacturer: Maxim Integrated Products
• Type: Metering SoCr

Specifications of 71M6511-IGTR/F

• Mounting Style: SMD/SMT
• Package / Case: LQFP-64
• Core: 80515 MPU
• Data Bus Width: 32 bit
• Data Ram Size: 7 KB
• Device Million Instructions Per Second: 5 MIPS
• Interface Type: UART
• Maximum Clock Frequency: 70 Hz
• Maximum Operating Temperature: + 85 C
• Number Of Programmable I/os: 12
• Operating Supply Voltage: 3.3 V
• Processor Series: 71M6511
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin Descriptions
Power/Ground Pins
Name
GNDA
GNDD
V3P3A
V3P3D
VBAT
V2P5
VLCD
Analog Pins
Name
IA
VA
IB
V1
VREF
VBIAS
XIN
XOUT
VDRV
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output
The circuit number denotes the equivalent circuit, as specified under “I/O Equivalent Circuits”.
Page: 94 of 98
A Maxim Integrated Products Brand
Pin #
Pin #
49, 58
54
51
53
56
55
52
59
61
50
46
47
62
7
1
9
Type
Type
O
O
O
O
P
P
P
P
P
P
I
I
I
I
I
Description
Analog ground: This pin should be connected directly to the ground plane.
Digital ground: This pin should be connected directly to the ground plane.
Analog power supply: A 3.3V power supply should be connected to this pin.
Digital power supply: A 3.3V power supply should be connected to this pin.
Battery backup power supply. A battery or super-capacitor should be connected between
VBAT and GNDD. If no battery is used, connect VBAT to V3P3D.
Output of the internal 2.5V regulator. A 0.1µF capacitor to GNDA should be connected to this
pin.
LCD power supply. A DC source of 3.3V to 5.0V should be connected to this pin.
Circuit
6
6
6
7
9
9
8
4
© 2005–2010 Teridian Semiconductor Corporation
Description
Line Current Sense Input: This pin is a voltage input to the internal A/D converter.
Typically, it is connected to the output of a current transformer or shunt resistor. If
the pin is unused it must be connected to V3P3A or tied to the IB pin.
Line Voltage Sense Input: This pin is a voltage input to the internal A/D converter.
Typically, it is connected to the output of a resistor divider. If the pin is unused it
must be tied to V3P3A.
Line Current Sense Input: This pin is a voltage input to the internal A/D converter.
Typically, it is connected to the output of a current transformer or shunt resistor. If
the pin is unused it must be connected to V3P3A or tied to the IA pin.
Comparator Input: This pin is a voltage input to the internal comparator. The voltage
applied to the pin is compared to an internal reference voltage of 1.5V. If the input
voltage is above the reference, the comparator output will be high (1). If the
comparator output is low, a voltage fault will occur. See the precautions in the
Applications Section for terminating this pin.
Voltage Reference for the ADC. A 0.1µF capacitor to GNDA should be connected to
this pin.
This pin outputs the reference voltage used by the power fault detection circuit. A
1,000pF capacitor to GND should be connected to this pin.
Crystal Inputs: A 32kHz style crystal should be connected across these pins.
Typically, a 20pF capacitor is also connected from each pin to GNDA. It is important
to minimize the capacitance between these pins. See the crystal manufacturer
datasheet for details.
Voltage boost output.
Single-Phase Energy Meter IC
71M6511/71M6511H
DATA SHEET
NOVEMBER 2010
V2.7