71M6511H-IGT/F Maxim Integrated Products, 71M6511H-IGT/F Datasheet - Page 26

• Manufacturer Part Number: 71M6511H-IGT/F
• Description: IC ENERGY METER RESIDENT 64-LQFP
• Manufacturer: Maxim Integrated Products

Specifications of 71M6511H-IGT/F

• Processor Series: 6511x
• Core: 80515
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 7 KB
• Interface Type: I2C, SSI, UART
• Maximum Clock Frequency: 5 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: LQFP-64
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: 71M6511H-DB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 22 bit Delta Sigma
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 24 specifies the combinations of operation modes allowed for timer 0 and timer 1:
Timer 0 - mode 0
Timer 0 - mode 1
Timer 0 - mode 2
Timer/Counter Mode Control Register (PCON):
The SMOD bit in the PCON register doubles the baud rate when set.
WD Timer (Software Watchdog Timer)
The software watchdog timer is a 16-bit counter that is incremented once every 24 or 384 clock cycles. After a reset, the
watchdog timer is disabled and all registers are set to zero. The watchdog consists of a 16-bit counter (WDT), a reload register
(WDTREL), prescalers (by 2 and by 16), and control logic. Once the watchdog is started, it cannot be stopped unless the
internal reset signal becomes active.
Note: It is recommended to use the hardware watchdog timer instead of the software watchdog timer.
WD Timer Start Procedure: The WDT is started by setting the SWDT flag. When the WDT register enters the state 0x7CFF,
an asynchronous WDTS signal will become active. The signal WDTS sets bit 6 in the IP0 register and requests a reset state.
WDTS is cleared either by the reset signal or by changing the state of the WDT timer.
Page: 26 of 98
TCON.7
TCON.6
TCON.5
TCON.4
TCON.3
TCON.2
TCON.1
TCON.0
Bit
A Maxim Integrated Products Brand
MSB
SMOD
Symbol
TF1
TR1
TF0
TR0
IE1
IE0
IT1
IT0
Not allowed
The Timer 1 overflow flag is set by hardware when Timer 1 overflows. This flag
can be cleared by software and is automatically cleared when an interrupt is
processed.
Timer 1 Run control bit. If cleared, Timer 1 stops.
Timer 0 overflow flag set by hardware when Timer 0 overflows. This flag can be
cleared by software and is automatically cleared when an interrupt is
processed.
Timer 0 Run control bit. If cleared, Timer 0 stops.
Interrupt 1 edge flag is set by hardware when the falling edge on external pin
int1 is observed. Cleared when an interrupt is processed.
Interrupt 1 type control bit. Selects either the falling edge or low level on input
pin to cause an interrupt.
Interrupt 0 edge flag is set by hardware when the falling edge on external pin
int0 is observed. Cleared when an interrupt is processed.
Interrupt 0 type control bit. Selects either the falling edge or low level on input
pin to cause interrupt.
Function
Mode 0
YES
YES
© 2005–2010 Teridian Semiconductor Corporation
Table 23: The TCON Register Bit Functions
Table 25: The PCON Register
Not allowed
Timer 1
Table 24: Timer Modes
Mode 1
YES
YES
Single-Phase Energy Meter IC
Mode 2
YES
YES
YES
71M6511/71M6511H
DATA SHEET
LSB
NOVEMBER 2010
V2.7