TWR-MCF51MM Freescale Semiconductor, TWR-MCF51MM Datasheet

Page 1

... Quick Start Guide for TWR-MCF51MM MCF51MM256 The industry’s most complete solution for portable medical applications TOWER SYSTEM ...

Page 2

... Figure 1: TWR-MCF51MM Module TWR-MCF51MM-KIT Freescale Tower System The TWR-MCF51MM module is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today. ...

Page 3

... It is ideal for portable medical applications or any other application requiring a significant amount of precision analog such as instrumentation and industrial control. The TWR-MCF51MM-KIT features the 32-bit MCF51MM256 and consists of the following components: • TWR-MCF51MM—Also referred to as ...

Page 4

... TOWER SYSTEM Step-by-Step Installation Instructions In this Quick Start Guide, you will learn how to set up the TWR-MCF51MM-KIT. STEP Install Software 1 and Tools • Install CodeWarrior Development Studio for Microcontrollers V6.3 (Evaluation Version) • Install CodeWarrior for Microcontrollers V6.3.1 Patch • Processor Expert V3.09 (Graphical Code Generator) • Install Service Pack for MCF51MM • Install Flexis MM USB Bootloader GUI (Required for Lab 6) • ...

Page 5

... Quick Start Guide for TWR-MCF51MM Primary edge of TWR-MCF51MM and TWR-SER must connect to this Primary elevator, which has components on the bottom of the board, including the mini- USB connector. Figure 2: Tower System Assembled NOTE: Figure Tower System without the optional MED-EKG assembly. For details on how to assemble the MED-EKG, please refer to Lab 1 on the DVD ...

Page 6

... J26 2 and 3 J25 6 and 5, nothing on pin J24 Open J11 1 and and and 2 J18 1 and 2, 3 and 4, 5 and 6, 7 and 8, 9 and 10, 11 and 12, 13 and 14 SW3 Slider 1 at OFF (Position 1) Slider 2 at OFF (Position 2) Table 1: Default Settings on TWR-MCF51MM Module ...

Page 7

... EKG demo. Verify the MED-EKG module is configured to default settings. This is required to run the MED-EKG demo. Figure 4: MED-EKG with Default Jumpers Used in Table 2 NOTE: Please see MED-EKG schematic for jumper labels and functions. Jumper Default Setting on TWR-MCF51MM Module Name J2 1 and and and 3 ...

Page 8

... USB or damage could be caused. NOTE: When the TWR-MCF51MM module is used stand-alone, USB port (J17) is both the power source and the debugger interface. When the TWR-MCF51MM module is assembled as a Tower System, the USB port (J17) is only a OSBDM. LEDs correspond to silk-screened labels D9 to D12 on the TWR-MCF51MM module. ...

Page 9

... To program the MCF51MM256 with a different application, connect the USB from the PC to the TWR-SER, and then connect another USB from the PC to TWR-MCF51MM. If this is the first time you have connected the board, then a window may appear and ask about installing new hardware for the on-board OSBDM circuit ...

Page 10

... Real-Time Debugger window click (start and continue) to run the application. Rotate the potentiometer back and forth from the TWR-MCF51MM module. You will see that LED 1 to LED 4 will turn off and on sequentially depending upon the rotation of the potentiometer the same debugger window, you can click on this button to halt the application ...

Page 11

... GUI tool to update firmware via the MCF51MM256 USB interface NOTE: Lab 1 is printed and included in the MED- EKG box the TWR-MCF51MM KIT. Digital copies of all six labs are included in the DVD in the “Software” tab, “Labs” section. TOWER SYSTEM ...

Page 12

... For further information, visit freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, visit freescale.com/epp. To learn more about the TWR-MCF51MM-KIT and other Freescale medical products, please visit freescale.com/MCF51MM, freescale.com/medical and freescale.com/Tower. Freescale, the Freescale logo and CodeWarrior are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & ...