MGA-85563-TR1G Avago Technologies US Inc., MGA-85563-TR1G Datasheet
MGA-85563-TR1G
Specifications of MGA-85563-TR1G
MGA-85563-TR1G
Available stocks
Related parts for MGA-85563-TR1G
MGA-85563-TR1G Summary of contents
Page 1
... GHz. Packaged in an ultra-miniature SOT-363 package, it requires half the board space of a SOT-143 package. The MGA-85563 features a minimum noise figure of 1.6 dB and associated gain 1.9 GHz. The output is matched internally to 50Ω, and the input is par- tially matched, requiring only a single external inductor for optimal performance ...
Page 2
... MGA-85563 Absolute Maximum Ratings Symbol Parameter V , max Maximum Device Voltage Input Power in T Channel Temperature ch T Storage Temperature STG Electrical Specifications 25° Symbol Parameters and Test Conditions G Gain in Test Circuit test NF Noise Figure in Test Circuit test NF Minimum Noise Figure MIN (measured with G opt input and 50 Ω ...
Page 3
... Measured using the final test circuit shown below GHz. 3. Standard Deviation number is based on measurement of at least 500 parts from three non-consecutive wafer lots during the initial characteriza- tion of this product, and is intended to be used as an estimate for distribution of the typical specification. MGA-85563 Final Test Circuit 25°C, Z ...
Page 4
... MGA-85563 Typical Performance 25° Ω and using default of no external resistor at the 3.3V 3.0V 2. FREQUENCY (GHz) Figure 1. Minimum Noise Figure vs. Frequency and Voltage +85C +25C –40C FREQUENCY (GHz) Figure 4. Associated Gain vs. Frequency and Temperature. 6 +85C +25C 4 –40C FREQUENCY (GHz) Figure 7. Output Power @ 1 dB Gain Compression vs. ...
Page 5
... MGA-85563 Typical Performance, continued 25° Ω and using default of no external resistor at the +85C +25C –40C SUPPLY VOLTAGE (V) Figure 10. Device Current vs. Voltage and Temperature Input 6 4 Output FREQUENCY (GHz) Figure 13. Input and Output VSWR vs. Frequency 1dB CURRENT (mA) @ 2.0 GHz Figure 11. Output Third Order Intercept and P vs ...
Page 6
... MGA-85563 Typical Noise Parameters 25° Ω and using default of no external resistor at the Frequency F min (GHz) (dB) 0.2 1.63 0.5 1.61 0.9 1.60 1 ...
Page 7
... MHz. Application Guidelines The MGA-85563 is very easy to use. For most applications, all that is required to operate the MGA-85563 is to apply +3 volts to the RF Output pin, and noise match the RF Input. RF Input To achieve lowest noise figure performance, the input of the MGA-85563 should be matched from the system impedance (typically 50 Ω ...
Page 8
... If for any reason the R resistor is not located immedi- b ately adjacent to the MGA-85563 (such as in the case of remote current adjustment or to implement dynamic control of the device’s linearity), then a small series re- sistor (e.g., 10 Ω) should be located near the R de-Q the connection from the MGA-85563 to the exter- nal current-setting circuit ...
Page 9
... RF Input R Figure 22. Schematic of 1.9 GHz Circuit. DC bias is applied to the MGA-85563 through the RFC at the RF Output pin. The power supply connection is by- passed to ground with capacitor C3. Provision is made for an additional bypass capacitor, C4 added to the bias line near the +3 volt connection. C4 will not normal needed unless several stages are cascaded using ...
Page 10
... Since the input terminal of the MGA-85563 is at ground potential, the input DC blocking capacitor C1 need not be used unless the amplifier is connected to a preceding stage that has a voltage present at this point. The value of the DC blocking and RF bypass capacitors (C1 – C4) should be chosen to provide a small reactance (typically < ...
Page 11
... Typical values are intended to be used as a basis for electrical design. To assist designers in optimizing not only the immedi- ate amplifier circuit using the MGA-85563, but to also evaluate and optimize trade-offs that affect a complete wireless system, the standard deviation (σ) is provided for many of the Electrical Specifications parameters (at 25° ...
Page 12
... L 0.10 0.30 Part Number Ordering Information No. of Part Number Devices MGA-85563-TR1 3000 MGA-85563-TR2 10000 MGA-85563-BLK 100 MGA-85563-TR1G 3000 MGA-85563-TR2G 10000 MGA-85563-BLKG 100 Note: For lead-free option, the part number will have the character “G” at the end NOTES: 1. All dimensions are in mm. ...
Page 13
Device Orientation REEL USER FEED DIRECTION COVER TAPE Tape Dimensions and Product Orientation For Outline (CARRIER TAPE THICKNESS) 1 10° MAX DESCRIPTION SYMBOL CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER PERFORATION ...