MGA-82563-TR2G Avago Technologies US Inc., MGA-82563-TR2G Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
MGA-82563-TR2G
Manufacturer Part Number
MGA-82563-TR2G
Description
IC AMP MMIC GAAS 3V SOT-363
Manufacturer
Avago Technologies US Inc.
Type
General Purpose Amplifierr
Datasheet
1.MGA-82563-TR1G.pdf
(11 pages)
Specifications of MGA-82563-TR2G
P1db
17.3dBm
Noise Figure
2.2dB
Package / Case
SC-70-6, SC-88, SOT-363
Current - Supply
63mA ~ 101mA
Frequency
100MHz ~ 6GHz
Gain
13.5dB
Rf Type
Cellular, ISM, PHS, PCS, WLL, SATCOM
Test Frequency
2GHz
Voltage - Supply
2.7V ~ 3.3V
Operating Frequency
100 MHZ to 6 GHz
Operating Supply Voltage
5 V
Supply Current
105 mA
Mounting Style
SMD/SMT
Number Of Channels
1 Channel
Manufacturer's Type
MMIC Amplifier
Frequency (max)
6GHz
Operating Supply Voltage (typ)
3V
Package Type
SOT-363
Mounting
Surface Mount
Pin Count
6
Noise Figure (typ)
2.7@6000MHzdB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MGA-82563-TR2G
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Figure 19. Gain, Noise Figure, and Output Power vs. Supply Voltage.
There are several means of biasing the MGA-82563 at
3 volts in systems that use higher power supply voltages.
The simplest method, shown in Figure 20a, is to use a
series resistor to drop the device voltage to 3 volts. For
example, a 24 Ω resistor will drop a 5-volt supply to 3
volts at the nominal current of 84 mA. Some variation in
performance could be expected for this method due to
variations in current within the specified 63 to 101 mA
min/max range.
Figure 20. Biasing From Higher Supply Voltages.
A second method illustrated in Figure 20b, is to use for-
ward-biased diodes in series with the power supply. For
example, three silicon diodes connected in series will
drop a 5-volt supply to approximately 3 volts.
The use of the series diode approach has the advantage
9
(a)
22
20
18
16
14
12
10
8
6
4
2
0
+5 V
0
24 Ω
1
SUPPLY VOLTAGE (V)
Silicon
Diodes
(b)
+5 V
2
3
Power
Gain
NF
Zener
Diode
(c)
+5 V
4
of less dependency on current variation in the amplifiers
since the forward voltage drop of a diode is somewhat
current independent.
Reverse breakdown diodes (e.g., Zener diodes) could
also be used as in Figure 20c. However, care should be
taken to ensure that the noise generated by diodes in
either Zener or reverse breakdown is adequately filtered
(e.g., bypassed to ground) such that the diode’s noise is
not added to the amplifier’s signal.
Note that the voltage-dropping component in each of
these three methods must be able to safely dissipate up
to 200 mW.
SOT-363 PCB Footprint
A recommended PCB pad layout for the miniature SOT-
363 (SC-70) package used by the MGA-82563 is shown in
Figure 21 (dimensions are in inches). This layout provides
ample allowance for package placement by automated
assembly equipment without adding parasitics that
could impair the high frequency RF performance of the
MGA-82563. The layout is shown with a nominal SOT-363
package footprint superimposed on the PCB pads.
0.039
Figure 21. Recommended PCB Pad Layout for Avago’s SC70 6L/SOT-363 Products.
0.026
Dimensions in inches.
0.018
0.079