AMMC-6550-W10 Avago Technologies US Inc., AMMC-6550-W10 Datasheet
AMMC-6550-W10
Specifications of AMMC-6550-W10
Related parts for AMMC-6550-W10
AMMC-6550-W10 Summary of contents
Page 1
... GHz Image Rejection Mixer Data Sheet Description AMMC-6550 is an image rejection mixer (IRM), which can also be used mixer. The AMMC-6550 utilizes two distributed passive FET mixers and a Lange coupler realized in Avago Technologies unique 0.25µm gate length Enhancement mode PHEMT (E-PHEMT) technol- ogy ...
Page 2
... Symbol Parameters and Test Conditions V Gate Supply Operating Voltage g I Gate Supply Current (under any RF power drive and temperature) g Note: 1. Ambient operational temperature Ta=25°C unless otherwise noted. AMMC-6550 Typical performances (T Symbol Parameters and Test Conditions F RF Frequency Range Frequency Range LO ...
Page 3
... AMMC-6550 RF Specifications Parameters and Symbol Test Conditions [4] CG Conversion Gain IR Image Rejection Ratio Notes: 2. Small/Large signal data measured in a fully de-embedded test fixture from Ta=25°C. 3. Specifications are derived from measurements in 50Ω test environment. 4. 100% on-wafer RF testing is done at RF frequency = 19, 30, and 42GHz; IF frequency = 1GHz. ...
Page 4
... No ground wired are needed since ground connections are made with plated through-holes to the backside of the device. LSB USB 15-50GHz LO +0.4V Vg 100pF LO Figure 2. AMMC-6550 Assembly diagram for SSB mixer applications. 50Ω termination is required for the unwanted side-band termination Vg LO Figure 1. AMMC-6550 Schematic RF IF1 IF2 LO 15-50GHz +10dBm RF IF1 IF2 ...
Page 5
... AMMC-6550 Typical performances ( -10 -15 -20 -25 -30 - Frequency [GHz] Figure 3. Typical conversion Gain, Plo=+10dBm, Fif=1GHz 15 P-1[dBm] @Plo=14dBm 10 5 P-1[dBm] @Plo=10dBm 0 -5 CG[dB] @Plo=14dBm -10 CG[dB] @Plo=10dBm - Freq [GHz] Figure 5. Typical RF port input power (@P-1), Plo=+10dBm, Fif=1GHz Frf [GHz] Figure 7. Typical IP3, Fif=1GHz, Plo=10dBm and 15dBm = 25° ...
Page 6
Vgs[V] Figure 9. Typical Conversion gain vs. Gate voltage, Flo=30GHz, Plo=+10dBm and +13dBm 0 -5 -10 -15 -20 -25 -30 - Frequency ...
Page 7
Assembly Techniques The backside of the MMIC chip is RF ground. For mi- crostrip applications the chip should be attached directly to the ground plane (e.g. circuit carrier or heatsink) using [1,2] electrically conductive epoxy . For conductive epoxy, the ...
Page 8
... Ordering Information: AMMC-6550-W10 = 10 devices per tray AMMC-6550-W50 = 50 devices per tray For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. Obsoletes AV01-0394EN AV02-1285EN - June 9, 2009 www ...