ATA5771-DK1 Atmel, ATA5771-DK1 Datasheet - Page 188

• Manufacturer Part Number: ATA5771-DK1
• Description: BOARD XMITTER FOR ATA5771 868MHZ
• Manufacturer: Atmel
• Type: Transmitterr

Specifications of ATA5771-DK1

• Frequency: 868MHz
• Maximum Frequency: 868 MHz
• Supply Voltage (max): 4 V
• Supply Voltage (min): 2 V
• Supply Current: 8.5 mA
• Product: RF Development Tools
• For Use With/related Products: ATA5771
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.3
8.3.1
T
188
Notes:
A
Symbol Parameter
= –40°C to +85°C, V
V
R
I
V
V
V
V
V
V
R
ACLK
V
V
I
ACIO
RST
CC
IH1
IH2
OH
IL1
IL2
OL
IH
pu
IL
Microcontroller Block
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (10mA at V
4. Although each I/O port can source more than the test conditions (10mA at V
Atmel ATA5771/73/74
DC Characteristics
Input Low Voltage except
XTAL1 and RESET pin
Input low voltage, XTAL1
pin
Input high voltage, except
XTAL1 and RESET pins
Input high voltage, XTAL1
pin
Input low voltage, RESET
pin
Input high voltage, RESET
pin
Output low voltage
I/O pin except RESET
Output high voltage
I/O pin except RESET
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power-down mode
Analog comparator
Input offset voltage
Analog comparator
Input leakage current
ditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition. Pull up driving strenght of the PB3 RESET pad is weak.
Power Supply Current
CC
= 2.0V to 3.6V (unless otherwise noted)
(2)
(3)
,
,
Condition
V
= –40°C to +85°C
V
T
V
T
V
T
V
T
V
T
I
I
Active 4MHz, V
T
Idle 4MHz, V
T
WDT enabled, V
WDT disabled, V
V
V
T
V
V
T
= 1.8V to 3.6V
OL
OH
A
A
A
A
A
A
A
A
A
CC
CC
CC
CC
CC
CC
CC
in
CC
in
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= –40°C to +85°C
= 2mA, V
= V
= V
= –2mA, V
= 1.8V to 3.6V
= 1.8V to 3.6V
= 1.8V to 3.6V
= 1.8V to 3.6V
= 1.8V to 3.6V
= 1.8V to 3.6V
= 2.7V
= 2.7V
CC
CC
/2
/2
CC
CC
CC
CC
= 1.8V
= 3V
CC
CC
= 1.8V
= 3V
= 3V
= 3V
V
(1)
CC
T
A
0.7V
0.9V
0.9V
Min.
–0.5
–0.5
–0.5
–50
1.2
30
20
CC
CC
CC
(1)
(1)
(1)
CC
= 5V, 5mA at V
CC
= 5V, 5mA at V
Typ.
< 10
0.8
0.2
0.2
4
CC
+0.2V
+0.2V
+0.2V
= 3V) under steady state con-
V
V
V
CC
CC
CC
CC
Max.
+50
0.2
2.5
0.5
60
50
18
40
= 3V) under steady state
3
+ 0.5
+ 0.5
+ 0.5
CC
CC
CC
(1)
(1)
(1)
9137E–RKE–12/10
Unit
mA
mA
mV
µA
µA
nA
k
k
V
V
V
V
V
V
V
V