ATAB5429-9-WB Atmel, ATAB5429-9-WB Datasheet - Page 77
![KIT DEMO 915MHZ BLACKBIRD](/photos/14/12/141244/atab5429-9-wb_sml.jpg)
ATAB5429-9-WB
Manufacturer Part Number
ATAB5429-9-WB
Description
KIT DEMO 915MHZ BLACKBIRD
Manufacturer
Atmel
Type
Transceiver, UHFr
Specifications of ATAB5429-9-WB
Frequency
915MHz
Maximum Frequency
915 MHz
Output Power
0 dBm to 10 dBm
Supply Voltage (max)
6 V
Supply Voltage (min)
3 V
Supply Current
21 mA
Maximum Operating Temperature
+ 85 C
Board Size
2 in x 3.5 in
Minimum Operating Temperature
- 40 C
Product
RF Modules
For Use With/related Products
ATA5429
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ATAB-5429-9-WB
ATAB-5429-9-WB
ATAB-5429-9-WB
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for T
and V
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
4841D–WIRE–10/07
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
3.10
3.11 ASK modulation rate
No. Parameters
3.9
4.1
4.2
4.3 XTO start
4.4 Maximum C
4.5 Internal capacitors
4
VS2
Impedance RF_OUT in
RX mode
Noise floor power
amplifier
XTO
Pulling XTO due to XTO,
C
Transconductance XTO at
start
L1
= V
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50 according to
and C
VAUX
component values according to
with component values according to
-
= 5.0V (Base
L2
up time
0
tolerances
of XTAL
-
station Application). Typical values are given at f
Test Conditions
f
f
f
f
f
at ±10 MHz/at 5 dBm
f
f
f
f
f
This corresponds to
10 Kbit/s Manchester
coding and 20 Kbit/s
NRZ coding
Pulling at nominal
temperature and supply
voltage
f
frequency of the XTAL
C
R
C
C
At start
start
is regulated to V
C
C
R
Required for stable
operation with internal
load capacitors
C
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
XTAL
0
m
m
m
0
m
m
L1
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
< 14fF
and C
-
2.2 pF
= resonant
1.0 pF
7.0 fF
120
up the amplitude
120
14 fF
-
up; after
L2
Table 3-2 on page 12
amb
Table 3-7 on page
= 25°C, V
PPXTAL
ATA5423/ATA5425/ATA5428/ATA5429
VS1
24, 25
24, 25
24, 25 T
24, 25
24, 25
Pin
(10)
(10)
(10)
(10)
(10)
10
10
10
10
10
= V
(1)
VS2
and RF_OUT matched to 50 according to
22.
= 3.0V (1
Z
Z
Z
Z
Z
PWR_ON_IRQ_1
Symbol
RF_OUT_RX
RF_OUT_RX
RF_OUT_RX
RF_OUT_RX
RF_OUT_RX
f
C
Data_ASK
g
L
L
L
L
L
C
L1
TX10M
TX10M
TX10M
TX10M
TX10M
m, XTO
f
0max
XTO1
, C
L2
-
RF
battery application), V
= 433.92 MHz unless otherwise specified. Details
–
Min.
14.8
–
100
1
50
(2.8 – j141)
(2.6 – j135)
(36 – j502)
(33 – j480)
(19 – j366)
18 pF
–
–
–
–
–
Typ.
f
300
XTAL
19
127
126
126
125
125
VS2
= 6.0V (2-battery application)
Figure 3-1 on page 11
Figure 3-10 on page 21
+100
Max.
21.2
+50
800
3.8
10
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
Unit
ppm
kHz
ms
pF
pF
µs
Type*
with
C
C
C
C
C
C
C
C
C
C
C
A
B
A
D
B
77