MAX19700EVKIT Maxim Integrated Products, MAX19700EVKIT Datasheet - Page 3

• Manufacturer Part Number: MAX19700EVKIT
• Description: EVAL KIT FOR MAX19700
• Manufacturer: Maxim Integrated Products
• Type: Encoder, Decoderr

Specifications of MAX19700EVKIT

• For Use With/related Products: MAX19700
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Note: Indicate that you are using the MAX19700 when contacting these component suppliers.
• DC power supplies:
• Signal generator with low phase noise and low jitter
• Two signal generators with low phase noise for ana-
• Logic analyzer or data-acquisition system (e.g., HP
DESIGNATION QTY
AVX
Central Semiconductor
Coilcraft
Diodes Inc.
Fairchild
Panasonic
TDK
Texas Instruments
Vishay/Vitramon
Zetex USA
for clock input signal (e.g., HP 8662A, HP 8644B)
log signal inputs (e.g., HP 8662A, HP 8644B)
16500C, TLA621)
U4, U5
U1
U2
U3
U6
MAX19700 Evaluation Kit/Evaluation System
Analog (VDD)
Clock (CVDD)
Digital (OVDD)
Buffers (BVCC)
Op-Amp Positive (VOP)
Op-Amp Negative (VON)
SUPPLIER
1
1
1
2
1
_______________________________________________________________________________________
Recommended Equipment
Maxim MAX19700ETM (48-pin thin
QFN 7mm x 7mm)
20-bit dual-supply bus transceiver
(56-pin TSSOP)
Texas Instruments
SN74AVCH20T245GR
Maxim MAX9113ESA (8-pin SO)
Maxim MAX4108ESA (8-pin SO)
Maxim MAX4478AUD (14-pin TSSOP)
DESCRIPTION
843-946-0238
631-435-1110
847-639-6400
805-446-4800
888-522-5372
714-373-7366
847-803-6100
972-644-5580
203-268-6261
631-543-7100
Quick Start
PHONE
+3.0V, 100mA
+3.0V, 100mA
+1.8V, 100mA
+3.3V, 100mA
+5.0V, 250mA
-5.0V, 250mA
843-626-3123
631-435-1824
847-639-1469
805-446-4850
714-737-7323
847-390-4405
214-480-7800
203-452-5670
631-864-7630
• Analog bandpass filters (e.g., Allen Avionics, K&L
• Two spectrum analyzers (e.g., HP 8560E)
• One 10-bit digital pattern generator (e.g., Tektronix
The MAX19700 EV kit is a fully assembled and tested
surface-mount board. Follow the steps below to verify
board operation. Do not turn on power supplies or
enable signal/data generators until all connections
are completed.
Command Module Setup
1) Set both switches at SW1 to the OFF position to dis-
2) Place a shunt across pins 1-2 of the VDD select
DESIGNATION QTY
Microwave) for input signals and clock signal
DG2020A)
Component List (continued)
FAX
able the SDA/SCL pullup resistors.
jumper (command module working voltage set
to +3.3V).
—
None
None
None
U7
U8
1
1
8
1
1
www.avxcorp.com
www.centralsemi.com
www.coilcraft.com
www.diodes.com
www.fairchildsemi.com
www.panasonic.com
www.component.tdk.com
www.ti.com
www.vishay.com
www.zetex.com
Component Suppliers
Maxim MAX3023EUD (14-pin TSSOP)
Maxim MAX3027EUD (14-pin TSSOP)
Dual-supply 5-bit signal translator
(14-pin DQFN)
Fairchild FXL5T244
Shunts
MAX19700 PC board
MAX19700 EV kit software (CD-ROM)
DESCRIPTION
WEBSITE
Procedure
3