SA607DK/01,118 NXP Semiconductors, SA607DK/01,118 Datasheet - Page 8
![IC MIXER FM IF SYSTEM LV 20-SSOP](/photos/6/63/66383/20-ssop_sot266-1_sml.jpg)
SA607DK/01,118
Manufacturer Part Number
SA607DK/01,118
Description
IC MIXER FM IF SYSTEM LV 20-SSOP
Manufacturer
NXP Semiconductors
Series
SA607r
Datasheet
1.SA607DK01118.pdf
(19 pages)
Specifications of SA607DK/01,118
Package / Case
20-SSOP
Rf Type
Cellular, ASK, FSK, NAMPS, NTACS
Frequency
150MHz
Number Of Mixers
2
Gain
19.5dB
Noise Figure
6.2dB
Secondary Attributes
Up Converter
Current - Supply
4.2mA
Voltage - Supply
2.7 V ~ 7 V
Maximum Input Frequency
150 MHz
Mounting Style
SMD/SMT
Maximum Operating Frequency
0.455 MHz
Maximum Power Gain
19.5 dB
Operating Supply Voltage
3 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
568-2034-2
935275287118
SA607DK/01-T
935275287118
SA607DK/01-T
1. C-message: The C-message and de-emphasis filter combination has a peak gain of 10 for accurate measurements. Without the gain, the
2. Ceramic filters: The ceramic filters can be 30kHz SFG455A3s made by Murata which have 30kHz IF bandwidth (they come in blue), or
3. RF generator: Set your RF generator at 45.000MHz, use a 1kHz modulation frequency and a 6kHz deviation if you use 16kHz filters, or
4. Sensitivity: The measured typical sensitivity for 12dB SINAD should be 0.35 V or –116dBm at the RF input.
5. Layout: The layout is very critical in the performance of the receiver. We highly recommend our demo board layout.
6. RSSI: The smallest RSSI voltage (i.e., when no RF input is present and the input is terminated) is a measure of the quality of the layout and
7. Supply bypass and shielding: All of the inductors, the quad tank, and their shield must be grounded. A 10-15 F or higher value tantalum
8. R5 can be used to bias the oscillator transistor at a higher current for operation above 45MHz. Recommended value is 22k , but should not
Philips Semiconductors
NOTES:
1997 Nov 07
Low voltage high performance mixer FM IF system
measurements may be affected by the noise of the scope and HP339 analyzer. The de-emphasis filter has a fixed -6dB/Octave slope
between 300Hz and 3kHz.
16kHz CFU455Ds, also made by Murata (they come in black). All of our specifications and testing are done with the more wideband filter.
8kHz if you use 30kHz filters.
design. If the lowest RSSI voltage is 500mV or higher, it means the receiver is in regenerative mode. In that case, the receiver sensitivity
will be worse than expected.
capacitor on the supply line is essential. A low frequency ESR screening test on this capacitor will ensure consistent good sensitivity in
production. A 0.1 F bypass capacitor on the supply pin, and grounded near the 44.545MHz oscillator improves sensitivity by 2-3dB.
be below 10k .
RF GENERATOR
45MHz
V
CC
Figure 5. SA607 Application Circuit Test Set Up
(+3)
SCOPE
DC VOLTMETER
8
HP339A DISTORTION
SA607 DEMO-BOARD
RSSI
ANALYZER
DE-EMPHASIS
C–MESSAGE
FILTER
AUDIO
Product specification
SA607
SR00391