SI4705-C40-GM Silicon Laboratories Inc, SI4705-C40-GM Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI4705-C40-GM
Manufacturer Part Number
SI4705-C40-GM
Description
IC RX FM RADIO 64-108MHZ 20UQFN
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI4705-C-EVB.pdf
(36 pages)
Specifications of SI4705-C40-GM
Frequency
64MHz ~ 108MHz
Modulation Or Protocol
FM
Applications
General Purpose
Current - Receiving
19.9mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Features
RSSI Equipped
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-20°C ~ 85°C
Package / Case
20-UQFN, 20-µQFN
Pin Count
20
Screening Level
Commercial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sensitivity
-
Memory Size
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SI4705-C40-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Si4704/05-C40
4.10. Tuning
The tuning frequency can be directly programmed using
the
supports channel spacing steps of 10 kHz in FM mode.
4.11. Seek
Seek tuning will search up or down for a valid channel.
Valid channels are found when the receive signal
strength indicator (RSSI) and the signal-to-noise ratio
(SNR) values exceed the set threshold. Using the SNR
qualifier rather than solely relying on the more
traditional RSSI qualifier can reduce false stops and
increase the number of valid stations detected. Seek is
initiated using the FM_SEEK_START command. The
RSSI and SNR threshold settings are adjustable using
properties (see Table 14).
4.12. Reference Clock
The Si4704/05 reference clock is programmable,
supporting RCLK frequencies in Table 11. Refer to
Table 3, “DC Characteristics,” on page 5 for switching
voltage
Characteristics,” on page 12 for frequency tolerance
information.
An onboard crystal oscillator is available to generate the
32.768 kHz reference when an external crystal and load
capacitors are provided. Refer to "2. Typical Application
Schematic" on page 16. This mode is enabled using the
POWER_UP command. Refer to Table 13, “Selected
Si4704/05 Commands,” on page 25.
The Si4704/05 performance may be affected by data
activity on the SDIO bus when using the integrated
internal oscillator. SDIO activity results from polling the
tuner for status or communicating with other devices
that share the SDIO bus. If there is SDIO bus activity
while the Si4704/05 is performing the seek/tune
function, the crystal oscillator may experience jitter,
which may result in mistunes, false stops, and/or lower
SNR.
For
recommends that all SDIO data traffic be suspended
during Si4704/05 seek and tune operations. This is
achieved by keeping the bus quiet for all other devices
on the bus, and delaying tuner polling until the tune or
seek operation is complete. The seek/tune complete
(STC) interrupt should be used instead of polling to
determine when a seek/tune operation is complete.
22
FM_TUNE_FREQ
best seek/tune
levels
and
results,
command.
Table 9,
Silicon
The
“FM
Laboratories
Si4704/05
Receiver
Rev. 1.0
4.13. Control Interface
A serial port slave interface is provided, which allows an
external controller to send commands to the Si4704/05
and receive responses from the device. The serial port
can operate in three bus modes: 2-wire mode, 3-wire
mode, or SPI mode. The Si4704/05 selects the bus
mode by sampling the state of the GPO1 and GPO2
pins on the rising edge of RST. The GPO1 pin includes
an internal pull-up resistor, which is connected while
RST is low, and the GPO2 pin includes an internal pull-
down resistor, which is connected while RST is low.
Therefore, it is only necessary for the user to actively
drive pins which differ from these states. See Table 12.
After the rising edge of RST, the pins GPO1 and GPO2
are used as general purpose output (O) pins as
described in Section “4.14. GPO Outputs”. In any bus
mode, commands may only be sent after V
supplies are applied.
In any bus mode, before sending a command or reading
a response, the user must first read the status byte to
ensure that the device is ready (CTS bit is high).
4.13.1. 2-Wire Control Interface Mode
When selecting 2-wire mode, the user must ensure that
SCLK is high during the rising edge of RST, and stays
high until after the first start condition. Also, a start
condition must not occur within 300 ns before the rising
edge of RST.
The 2-wire bus mode uses only the SCLK and SDIO
pins for signaling. A transaction begins with the START
condition, which occurs when SDIO falls while SCLK is
high. Next, the user drives an 8-bit control word serially
on SDIO, which is captured by the device on rising
edges of SCLK. The control word consists of a 7-bit
device address, followed by a read/write bit (read = 1,
write = 0). The Si4704/05 acknowledges the control
word by driving SDIO low on the next falling edge of
SCLK.
Table 12. Bus Mode Select on Rising Edge of
Bus Mode
2-Wire
3-Wire
SPI
0 (must drive)
GPO1
RST
1
1
1 (must drive)
GPO2
IO
0
0
and V
DD