TDA5200 Infineon Technologies, TDA5200 Datasheet - Page 20

• Manufacturer Part Number: TDA5200
• Description: IC LP SGL CONV ASK P-TSSOP-28
• Manufacturer: Infineon Technologies
• Type: Receiverr

Specifications of TDA5200

• Package / Case: 28-TSSOP
• Frequency: 433MHz, 868MHz
• Sensitivity: -107dBm
• Modulation Or Protocol: ASK
• Applications: Alarm Systems, Communication Systems
• Current - Receiving: 4.8mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Operating Frequency: 870 MHz
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 4.4mm
• Product Length (mm): 9.7mm
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SP000016381; TDA5200INTR; TDA5200XT; TDA5200XT; TDA5200XTINTR; TDA5200XTINTR

3.4.4
The on-chip crystal oscillator circuitry allows for utilization of quartzes both in the 6 MHz and 13 MHz range as the
overall division ratio of the PLL can be switched between 64 and 128 via the CSEL (Pin 16) pin according to the
following table.
Table 3
CSEL
Open
Shorted to ground
The calculation of the value of the necessary quartz load capacitance is shown in
frequency calculation is explained in
3.4.5
The Limiter is an AC coupled multistage amplifier with a cumulative gain of approximately 80 dB that has a
bandpass-characteristic centered around 10.7 MHz. It has an input impedance of 330 Ω to allow for easy
interfacing to a 10.7 MHz ceramic IF filter. The limiter circuit acts as a Receive Signal Strength Indicator (RSSI)
generator which produces a DC voltage that is directly proportional to the input signal level as can be seen in
Figure
turn down the LNA gain by approximately 17 dB in case the input signal strength is too strong as described in
Chapter 3.4.1
3.4.6
The data filter comprises an OP-Amp with a bandwidth of 100 kHz used as a voltage follower and two 100 kΩ on-
chip resistors. Along with two external capacitors a 2
the capacitor values is described in
3.4.7
The data slicer is a fast comparator with a bandwidth of 100 kHz. This allows for a maximum receive data rate of
approximately 120 kBaud. The maximum achievable data rate also depends on the IF Filter bandwidth and the
local oscillator tolerance values. Both inputs are accessible. The output delivers a digital data signal (CMOS-like
levels) for the detector. The self-adjusting threshold on pin 20 is generated by RC-term or peak detector
depending on the baseband coding scheme. The data slicer threshold generation alternatives are described in
more detail in
3.4.8
The peak detector generates a DC voltage which is proportional to the peak value of the receive data signal. An
external RC network is necessary. The output can be used as an indicator for the signal strength and also as a
reference for the data slicer. The maximum output current is 500 µA.
3.4.9
A Bandgap Reference Circuit provides a temperature stable reference voltage for the device. A power down mode
is available to switch off all sub-circuits which is controlled by the PWDN pin (Pin 27) as shown in the following
table. The supply current drawn in this case is typically 50 nA.
Data Sheet
6. This signal is used to demodulate the ASK receive signal in the subsequent baseband circuitry and to
Bandgap Reference Circuitry
Crystal Oscillator
CSEL Pin Operating States
Limiter
Data Filter
Data Slicer
Peak Detector
Chapter
and
Chapter
4.5.
4.1.
Chapter
Chapter
4.2.
4.4.
nd
order Sallen-Key low pass filter is formed. The selection of
20
Crystal Frequency
6.xx MHz
13.xx MHz
ASK Single Conversion Receiver
Revision 3.0, 2010-12-28
Functional Description
Chapter
4.3, the quartz
TDA 5200