ATMEGA256RZBV-8CU Atmel, ATMEGA256RZBV-8CU Datasheet - Page 6
![BUNDLE ATMEGA2560V/AT86RF230-ZU](/photos/6/89/68968/313-100-cbga_sml.jpg)
ATMEGA256RZBV-8CU
Manufacturer Part Number
ATMEGA256RZBV-8CU
Description
BUNDLE ATMEGA2560V/AT86RF230-ZU
Manufacturer
Atmel
Series
ATMEGAr
Datasheet
1.ATMEGA64RZAPV-10MU.pdf
(21 pages)
Specifications of ATMEGA256RZBV-8CU
Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Applications
ISM, ZigBee™
Power - Output
3dBm
Sensitivity
-101dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
15.5mA
Current - Transmitting
16.5mA
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 4kB EEPROM, 8kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
100-TFBGA
Wireless Frequency
2.4 GHz
Interface Type
SPI, USART
Output Power
3 dBm
For Use With
ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Operating Temperature
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega256
3.4.4 Reset Line
3.4.5 Pins used by the RZ502
6
AVR414
This line is used to reset the AT86RF230 radio transceiver. The reset line is
controlled by one of the AVR pins and not connected to the reset button on the
STK500 board.
Table 3-1 lists the 17 pins used by the RZ502 top module and their usage. This
information can be used to run the Accessory Kit on alternative platforms. Remaining
pins of the expansion connector 1 is not connected.
NOTE: Be sure that none of the pins used by the RZ502 top module is connected to
other circuitry. I.e. no additional circuitry can be connected to the SPI pins of the
PORTB connector on the STK500 etc.
Table 3-1. Pins used by the RZ502 board
Expansion Connector 1 Pin
Notes:
1,2,21,22,39,40
1. Pins connected to the same net. Only one required if number of pins is scarce.
2. Not connected by default. Requires de-soldering R1 (0 Ω) and soldering onto
19,20
the R2 pads.
17
25
26
27
28
29
30
32
34
(2)
(1)
(1)
Name
GND
VTG
PB5
PB4
PB3
PB2
PB1
PB0
PD6
PD4
XT1
Usage
Used for analog and digital ground.
Target voltage. Must be within the
operating range of the AT86RF230 [1.8 to
3.6 Volts].
Can be used to connect the CLKM pin on
the AT86RF230 to the AVR’s XT1 pin.
Reset line. Connected to the RST pin on
the AT86RF230.
Connected to the SLP_TR pin on the
AT86RF230.
MISO line.
MOSI line.
SCK line.
SEL line.
Used to connect the CLKM pin of the
AT86RF230 to the Timer1 module on the
AVR.
Connected to the IRQ pin on the
AT86RF230.
8051A-AVR-11/06