JN5148-001-M00T NXP Semiconductors, JN5148-001-M00T Datasheet - Page 3

MODULE ZIGBEE PRO CERM ANTENNA

JN5148-001-M00T

Manufacturer Part Number
JN5148-001-M00T
Description
MODULE ZIGBEE PRO CERM ANTENNA
Manufacturer
NXP Semiconductors
Series
JN5148r
Datasheets

Specifications of JN5148-001-M00T

Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Applications
AMR, ISM, Home Automation, Process Control
Power - Output
2.5dBm
Sensitivity
-95dBm
Voltage - Supply
2.3 V ~ 3.6 V
Current - Receiving
17.5mA
Current - Transmitting
15mA
Data Interface
PCB, Surface Mount
Memory Size
4Mbit Flash, 128kB RAM, 128kB ROM
Antenna Connector
On-Board, Chip
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Rate - Maximum
-
Other names
616-1045-2
935294034534
JN5148-001-M00T
1.1. Variants
1.2. Regulatory Approvals
1. Introduction
The JN5148-001-Myy module family provides designers with a ready made component that provides a fully
integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1],
including JenNet and ZigBee PRO, and can be quickly and easily included in product designs. The modules
integrate all of the RF components required, removing the need to perform expensive RF design and test. Products
can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single
chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development
support material. Hence, this range of modules allows designers to bring wireless applications to market in the
minimum time with significantly reduced development effort and cost.
Three variants are available: JN5148-001-M00 (standard module with integral antenna), JN5148-001-M03 (standard
module with uFl connector for use with external antennae) and JN5148-001-M04 (high RF power with uFL connector,
improved sensitivity module for evaluation of extended range applications).
approvals and are compliant with EU regulations. The variants available are described below.
Variant
JN5148-001-M00
JN5148-001-M03
JN5148-001-M04
All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a
Notified Body statement of opinion for this standard is available on request. The High Power module with M04 suffix
is approved for use in Europe with reduced output power: +10dBm EIRP is the maximum permitted in Europe.
Additionally, all module types have received FCC “Modular Approvals”, in compliance with CFR 47 FCC part 15
regulations and in accordance to FCC Public notice DA00-1407, appendix A.7 contains details on the conditions
applying to this modular approval. The modules are approved for use with a range of different antennas; further
details of which can be found in section Appendix A.6.1. The modular approvals notice and test reports are available
on request.
The high power module variant is classified as ‘mobile’ device pursuant with FCC § 2.1091 and must not be used at a
distance of less than 20 cm (8”) from any person.
In addition, all modules have Industry Canada modular approval and RSS210e Issue 7 (June 2007) certification.
© NXP Laboratories UK 2010
Description
Standard Power, integrated antenna
Standard Power, uFl connector
High Power, uFl connector
JN-DS-JN5148-001-Myy 1v4
FCCID
TYOJN5148M0
TYOJN5148M3
TYOJN5148M4
All modules have FCC modular
Industry Canada ID
IC: 7438A-CYO5148M0
IC: 7438A-CYO5148M3
IC: 7438A-CYO5148M4
3

Related parts for JN5148-001-M00T