RN-24S Roving Networks Inc, RN-24S Datasheet - Page 14

• Manufacturer Part Number: RN-24S
• Description: SUPERMODULE BLUETOOTH CHIP ANT
• Manufacturer: Roving Networks Inc

Specifications of RN-24S

• Frequency: 2.4GHz
• Data Rate - Maximum: 721kbps
• Modulation Or Protocol: Bluetooth v2.0+EDR, Class 1 & 2
• Applications: Bluetooth v2.0
• Power - Output: 4dBm
• Sensitivity: -80dBm
• Voltage - Supply: 4 V ~ 24 V
• Current - Receiving: 40mA
• Current - Transmitting: 40mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: On-Board, Chip
• Package / Case: Module
• Wireless Frequency: 2.402 GHz to 2.48 GHz
• Interface Type: UART
• Data Rate: 240 Kbps to 300 Kbps
• Modulation: FHSS, GFSK
• Operating Voltage: 3.3 V
• Antenna: Chip Antenna
• Board Size: 20.32 mm x 50.8 mm x 4.08 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 740-1008

www.rovingnetworks.com
I<,time>,<COD>
IN<time>,<cod>
IS<time>
IR<time>
H
K,
L
P,<char>
Q
R,1
T,<0,1>
W
809 University Avenue
Performs an inquiry scan. Default time is 10 seconds, maximum is 48. COD
parameter is optional, 0 or no entry looks for all device classes. When entering a
COD you must provide all six characters, i.e. 0040F0 for COD 0x40F0. A maximum
of 9 devices will be returned. As devices are found, they are displayed in the format
below:
Performs an inquiry scan like the I command but does not return the Bluetooth name
so it returns much faster since getting the name requires a remote lookup for each
device found.
Performs an inquiry scan, with a COD of 0x001F00, which is the default COD for
Roving Networks Serial adapters and modules.
Performs an inquiry scan, with a COD of 0x0055AA, which is the special COD used
By Roving Networks Serial adapters and modules to enable “instant cable
replacement”.
Help, will print out a list of commands and their basic syntax
Kill (disconnect) from the current connection. The characters KILL<cr><lf> will be
echoed to the local UART once the connection is broken.
Link Quality. Returns real-time streaming link quality values at 5Hz. Value
returned is a two bytes separated by a comma. A value of “ff” is the highest value.
The first byte is the current reading the second byte is the low water mark.
Example output:
Passes thru any characters up to a CR or LF while in command mode.
Causes device to be non-discoverable and non-connectable (temporarily). Does not
survive a power cycle or reset. Used with the Z command below. Use the “W”
command to re-enable.
This command will return “Quiet” as a response.
To get the lowest power mode, first issue a Q, then a Z. Use the SNIFF settings to
get lowest power while connected.
Forces a complete reboot of the device (similar to a power cycle).
Pass receive data (from UART or BT) while in command mode. Returns (T=0 , T=1
based on input).
Re-enables discovery and connection. This command reloads the stored value of the
Inquiry and Page Window to re-enable. For example, to turn off Discovery but still
allow connections, send an “SI,0000” command, and follow it with “W” command.
This command returns “Wake” as a response.
•
Los Gatos, CA 95032
RSSI =ff,e6
<BT address>,<BT name>,<COD>
00A053000123,MySerialPort,72010C
~ 14 ~
•
Tel [phone]
rn-bluetooth-um Version 4.77 1/24/2011
Advanced User Manual
• [e-mail]