ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 504

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

34.4 Power Supply Currents (RF transceiver in SLEEP mode)
Test Conditions: T
504
Symbol
V
V
V
V
V
V
R
R
I
I
Symbol
I
IL
IH
SUPPLY
Note:
IHRSTN
ILRSTN
OH
OL
OHMIN
OLMIN
RSTN
GPIO
Parameter
High level input voltage
Low level input voltage
High level output voltage
Low level output voltage
High level output voltage
Low level output voltage
Reset pull-up resistor
GPIO pull-up resistor
Input Leakage current
Input Leakage current
Parameter
Power Supply Current
(PRR0=0xFF, PRR1=0x3F,
16MHz RC Oscillator selected)
Power Supply Current
(PRR0=0x00, PRR1=0x00)
DEEP_SLEEP (AVR in Power Down
mode, all SRAM enabled, WDT
disabled)
1.
ATmega128RFA1
The capacitive load should not be larger than 50 pF for all I/Os when using the default driver strength settings, refer
to section
on page
OP
= 25°C, V
176. Generally, large load capacitances increase the overall current consumption.
"DPDS0 – Port Driver Strength Register 0" on page 175
DD
(1)
(1)
(1)
(1)
(1)
(1)
=3.0V (unless otherwise stated)
Condition
Pin RSTN
Pin RSTN
I
I
Maximum. drive strength by DPDS0/1
Except Pins 17,18
I
I
Maximum drive strength by DPDS0/1
Except Pins 17,18
I
I
Minimum drive strength by DPDS0/1
I
I
Minimum. drive strength by DPDS0/1
If pull-up resistor is enabled
V
T = 25 ° C
V
T = 25 ° C
Condition / AVR mode
Standby mode
Idle 1MHz
Idle 8MHz
Idle 16MHz
Active 1MHz
Active 8MHz
Active 16MHz
Active, 16MHz RC Oscillator
Active, external 16MHz clock on CLKI
T = 25 ° C
T = 85 ° C
T = 125 ° C
OH
OH
OL
OL
OH
OH
OL
OL
DD
DD
= 16mA, V
= 10mA, V
= 4mA, V
= 2.5mA, V
= -12mA, V
= -6mA, V
= -3mA, V
= -1.5mA, V
= 3.6V, pin low
= 3.6V, pin high
DD
DD
DD
DD
DD
DD
DD
= 3.6V
DD
= 1.8V
= 3.6V
= 3.6V
= 1.8V
= 1.8V
= 3.6V
= 1.8V
and
"DPDS1 – Port Driver Strength Register 1"
0.9 V
V
V
Min
Min
120
120
0.4
0.4
DD
DD
DD
–
–
0.31
0.45
0.25
Typ
<10
<10
Typ
0.8
1.1
0.8
2.5
3.7
4.0
4.5
1.5
15
8266B-MCU Wireless-03/11
0.1 V
Max
Max
360
360
0.4
0.4
1
1
DD
Units
V
V
V
V
V
V
k
k
µA
nA
µA
nA
Units
mA
mA
mA
mA
mA
mA
mA
mA
mA
µA
µA
µA