XBP09-DPUIT-156 Digi International, XBP09-DPUIT-156 Datasheet - Page 49

• Manufacturer Part Number: XBP09-DPUIT-156
• Description: MODULE XBEE PRO W/U.FL
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP09-DPUIT-156

• Frequency: 902MHz ~ 928MHz
• Data Rate - Maximum: 156kbps
• Modulation Or Protocol: FHSS
• Applications: ISM
• Power - Output: 17dBm (50mW)
• Sensitivity: -100dBm
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Receiving: 80mA
• Current - Transmitting: 210mA
• Data Interface: PCB, Through Hole
• Antenna Connector: U.FL
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1168

XBee‐PRO® 900 RF Modules
Explicit Addressing Command Frame
Example: The example above shows how to send a transmission to a module where escaping is
disabled (AP=1) with destination address 0x0013A200 40014011, payload "TxData0A". If
escaping is enabled (AP=2), the frame should look like:
The checksum is calculated (on all non-escaped bytes) as [0xFF - (sum of all bytes from API frame
type through data payload)].
Frame Type: 0x11
Allows application layer fields (endpoint and cluster ID) to be specified for a data transmission.
Similar to the Transmit Request, but also requires application layer addressing fields to be
specified (endpoints, cluster ID, profile ID). An Explicit Addressing Request API frame causes the
module to send data as an RF packet to the specified destination, using the specified source and
destination endpoints, cluster ID, and profile ID.
The 64-bit destination address should be set to 0x000000000000FFFF for a broadcast
transmission (to all devices). For unicast transmissions the 64 bit address field should be set to the
address of the desired destination node. The reserved field should be set to 0xFFFE.
A
P
I
P
a
c
k
e
t
0x7E 0x00 0x16 0x10 0x01 0x00 0x7D 0x33 0xA2 0x00 0x40 0x0A 0x01 0x27
0xFF 0xFE 0x00 0x00 0x54 0x78 0x44 0x61 0x74 0x61 0x30 0x41 0x7D 0x33
© 2009 Digi International, Inc.
Start Delimiter
Length
Frame-specific Data
Checksum
Frame Fields
Frame Type
Frame ID
64-bit Destination
Address
Reserved
Broadcast Radius
Transmit Options
RF Data
Offset Example
LSB 12 0x27
MSB 1 0x00
MSB 5 0x00
LSB 2 0x16
10 0x0A
13 0xFF
14 0xFE
15 0x00
16 0x00
17 0x54
18 0x78
19 0x44
20 0x61
21 0x74
22 0x61
23 0x30
24 0x41
25 0x13
11 0x01
0 0x7E
3 0x10
4 0x01
6 0x13
7 0xA2
8 0x00
9 0x40
Number of bytes between the length and the checksum
Identifies the UART data frame for the host to correlate
with a subsequent ACK (acknowledgement). If set to 0,
no response is sent.
Set to the 64-bit address of the destination device. The
following address is also supported:
0x000000000000FFFF - Broadcast address
Set to 0xFFFE.
Sets maximum number of hops a broadcast transmission
can occur. If set to 0, the broadcast radius will
be set to the maximum hops value.
Bitfield:
bit 0: Disable ACK
bit 1: Don't attempt route Discovery.
All other bits must be set to 0.
Data that is sent to the destination device
0xFF - the 8 bit sum of bytes from offset 3 to this byte.
Description
49