X09-009NSC-TX Digi International/Maxstream, X09-009NSC-TX Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
X09-009NSC-TX
Manufacturer Part Number
X09-009NSC-TX
Description
MOD RF TX 900MHZ 9600BPS W/RPSMA
Manufacturer
Digi International/Maxstream
Specifications of X09-009NSC-TX
Frequency
900MHz
Data Rate - Maximum
19.2kbps
Modulation Or Protocol
FSK
Power - Output
100mW
Sensitivity
-110dBm
Voltage - Supply
5V
Current - Receiving
50mA
Current - Transmitting
140mA
Data Interface
PCB, Through Hole
Antenna Connector
RP-SMA
Operating Temperature
0°C ~ 70°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Memory Size
-
XStream™ OEM RF Module – Product Manual v5.x00 [2006.02.24]
BK (Serial Break Passing) Command
BO (Serial Break Timeout) Command
BT (Guard Time Before) Command
CB (Connection Duration Timeout) Command
CC (Command Sequence Character) Command
<Serial Interfacing> Pass a serial break condition
on the DI pin to the DO pin of another module.
<Serial Interfacing> DO pin will return to default
after no serial break status information is
received during the timeout period.
Use with BK parameter = 1.
<Command Mode Options> BT Command is used
to set the DI pin silence time that must precede
the command sequence character (CC
Command) of the AT Command Mode Sequence.
Refer to the AT Commands section [p16] to view
the default AT Command Mode sequence.
<Networking & Security> Set/Read the
maximum amount of time an exclusive
connection between a base and remote module
in a point-to-multipoint network is sustained. The
remote module will disconnect when this timeout
expires.
<Command Mode Options> CC Command is used
to set the ASCII character to be used between
Guard Times of the AT Command Mode Sequence
(BT+ CC + AT). The AT Command Mode
Sequence activates AT Command Mode (from
Idle Mode).
Refer to the AT Commands section [p16] to view
the default AT Command Mode sequence.
© 2006 MaxStream, Inc. Confidential and Proprietary
AT Command: ATBK
Binary Command: 0x2E (46 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: BO (Serial Break Timeout)
Minimum Firmware Version Required: 4.30
AT Command: ATBO
Binary Command: 0x30 (48 decimal)
Parameter Range: 0 – 0xFFFF [x 1 second]
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: BK (Serial Break Passing)
Minimum Firmware Version Required: 4.30
AT Command: ATBT
Binary Command: 0x04 (4 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0x0A (10 decimal)
Number of bytes returned: 2
Related Commands: AT (Guard Time After), CC
(Command Sequence Character)
AT Command: ATCB
Binary Command: 0x33 (51 decimal)
Parameter Range: 0x01 – 0xFFFF
Default Parameter Value: 0x28 (4d seconds)
Number of bytes returned: 2
Related Commands: CE (Connection Inactivity
Timeout), DC (Disconnect), MD (RF Mode)
Minimum Firmware Version Required: 4.30
AT Command: ATCC
Binary Command: 0x13 (19 decimal)
Parameter Range: 0x20 – 0x7F
Default Parameter Value: 0x2B (ASCII “+” sign)
Number of bytes returned: 1
Related Commands: AT (Guard Time After), BT
(Guard Time Before)
Parameter
0
1
[x 100 milliseconds]
[x 100 milliseconds]
Configuration
disable
enable
21