X09-009NSC-TX Digi International/Maxstream, X09-009NSC-TX Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
X09-009NSC-TX
Manufacturer Part Number
X09-009NSC-TX
Description
MOD RF TX 900MHZ 9600BPS W/RPSMA
Manufacturer
Digi International/Maxstream
Specifications of X09-009NSC-TX
Frequency
900MHz
Data Rate - Maximum
19.2kbps
Modulation Or Protocol
FSK
Power - Output
100mW
Sensitivity
-110dBm
Voltage - Supply
5V
Current - Receiving
50mA
Current - Transmitting
140mA
Data Interface
PCB, Through Hole
Antenna Connector
RP-SMA
Operating Temperature
0°C ~ 70°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Memory Size
-
XStream™ OEM RF Module – Product Manual v5.x00 [2006.02.24]
FH (Force Wake-up Initializer) Command
FL (Software Flow Control) Command
FT (Flow Control Threshold) Command
GD (Receive Good Count) Command
HP (Hopping Channel) Command
<Sleep (Low Power)> FH Command is used to
force a Wake-up Initializer to be sent on the next
transmission. WR (Write) Command does not
need to be issued with FH Command.
Use only with cyclic sleep modes active on remote modules.
<Serial Interfacing> FL Command is used to
configure of module with software flow control.
Hardware flow control is implemented with the
XStream Module as the DO2 pin (
regulates when serial data can be transferred to
the module. FL Command is used to allow
software flow control. XON character used is
0x11 (17 decimal). XOFF character used is 0x13
(19 decimal).
<Serial Interfacing> Set/Read the flow control
threshold. When FT bytes have accumulated in
the DI buffer,
software flow control character is transmitted.
<Diagnostics> Set/Read the count of good
received RF packets. Parameter value is reset to
0 after every reset and is not non-volatile (value
does not persist in the module’s memory after a
power-up sequence). Once the “Receive Good
Count” reaches its maximum value (up to
0xFFFF), it remains at its maximum count value
until the maximum count value is manually changed or the module is reset.
<Networking & Security> HP Command is used
to set the module hopping channel number. A
channel is one of three layers of addressing
available to the module. In order for modules to
communicate with each other, the modules must
have the same channel number since each
network uses a different hopping sequence.
Different channels can be used to prevent
modules in one network from listening to transmissions of another.
© 2006 MaxStream, Inc. Confidential and Proprietary
is de-asserted or the XOFF
), which
AT Command: ATFH
Binary Command: 0x0D (13 decimal)
AT Command: ATFL
Binary Command: 0x07 (7 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
AT Command: ATFT
Binary Command: 0x24 (36 decimal)
Parameter Range: 0 – 0xFF [bytes]
(Maximum value equals the receiving module
DO buffer size minus 0x11 bytes)
Default Parameter Value: Receiving module DO
Buffer size minus 0x11
Number of bytes returned: 2
Minimum Firmware Version Required: 4.27B
AT Command: ATGD
Binary Command: 0x10 (16 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: ER (Receive Error Count)
AT Command: ATHP
Binary Command: 0x11 (17 decimal)
Parameter Range: 0 – 6
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: DT (Destination Address),
ID (Module VID), MK (Address Mask)
Parameter
0
1
Disable software
Enable software
Configuration
flow control
flow control
25