PN5310A3HN/C203:55 NXP Semiconductors, PN5310A3HN/C203:55 Datasheet - Page 8

• Manufacturer Part Number: PN5310A3HN/C203:55
• Description: IC TRANSMISSION MOD 40-HVQFN
• Manufacturer: NXP Semiconductors

Specifications of PN5310A3HN/C203:55

• Rf Type: Read / Write
• Frequency: 13.56MHz
• Features: ISO14443A / Mifare
• Package / Case: 40-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935280844557; PN5310A3HN/C203; PN5310A3HN/C203

Philips Semiconductors
PN531
3.2 Pin Description
Pin
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
LOADMOD
OSC2OUT
OSCOUT
TESTEN
SIGOUT
OSC2IN
Symbol
TVSS1
TVSS2
OSCIN
AVDD
DVSS
TVDD
AVSS
SIGIN
VMID
AUX1
AUX2
TX1
TX2
P35
P34
RX
I0
I1
Type
PWR
PWR
PWR
PWR
PWR
PWR
PWR
IO
IO
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
Pad Ref
Voltage
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
TVDD
TVDD
AVDD
AVDD
AVDD
AVDD
SVDD
SVDD
SVDD
Description
Digital Ground
Load Modulation output provides digital signal for FeliCa and MIFARE®
card operating mode
Transmitter Ground: supplies the output stage of TX1 and TX2
Transmitter 1: delivers the modulated 13.56 MHz energy carrier
Transmitter power supply: supplies the output stage of TX1 and TX2
Transmitter 2: delivers the modulated 13.56 MHz energy carrier
Transmitter Ground: supplies the output stage of TX1 and TX2
Analog Power Supply
Internal Reference Voltage: This pin delivers the internal reference voltage.
Receiver Input: Input pin for the reception signal, which is the load
modulated 13.56 MHz energy carrier from the antenna circuit.
Analog Ground
Auxiliary Output: This pin delivers analog and digital test signals.
Auxiliary Output: This pin delivers analog and digital test signals.
Crystal Oscillator Input: input to the inverting amplifier of the oscillator. This
pin is also the input for an externally generated clock (fosc = 27.12 MHz).
Crystal Oscillator output: Output of the inverting amplifier of the oscillator.
Interface mode lines: selects the used host interface. In test mode I0 is
used as test signals.
Interface mode lines: selects the used host interface. In test mode I0 is
used as test signals.
Test enable pin: When set to 1 enable the test mode. When set to 0 reset
the TCB and disable the access to the test mode.
Crystal Oscillator output: Output of the inverting amplifier of the oscillator
for the USB clock.
Crystal Oscillator Input: input to the inverting amplifier of the oscillator for
the USB clock generation. This pin is also the input for an externally
generated clock (f
input
General purpose IO signal
General purpose IO signal or clk signal for the SAM
Contactless communication interface output: delivers a serial data stream
according to NFCIP-1 and output signal for the SAM. In test mode this
signal is used as test signal output.
Contactless communication interface input: accepts a digital, serial data
stream according to NFCIP-1 and input signal from the SAM. In test mode
Objective Short Form Specification Rev. 2.0 February 2004
8
µC based Transmission module
osc
=4 MHz). In test mode this signal is used as test clock