FSBB30CH60 Fairchild Semiconductor, FSBB30CH60 Datasheet
![SMART POWER MODULE 30A SPM27-EA](/photos/14/31/143142/fairchild_semiconductor-fsbb30ch60_sml.jpg)
FSBB30CH60
Specifications of FSBB30CH60
FSBB30CH60_NL
Available stocks
Related parts for FSBB30CH60
FSBB30CH60 Summary of contents
Page 1
... Fairchild Semiconductor Corporation FSBB30CH60 Rev. C General Description advanced smart power module (SPM has newly developed and designed to provide very compact and high performance ac motor drives mainly targeting low- power inverter-driven application like air conditioner and wash- ing machine ...
Page 2
... V (19) V (19) V (19) V (19) V (19) V B(W) B(W) B(W) B(W) B(W) B(W) (20) V (20) V (20) V (20) V (20) V (20) V S(W) S(W) S(W) S(W) S(W) S(W) FSBB30CH60 Rev. C Top View 13.7 13.7 13.7 (21) N (21) N (21) N (21 (22) N (22) N (22) N (22 19.2 19.2 19.2 ...
Page 3
... FSBB30CH60 Rev. C Pin Description Low-side Common Bias Voltage for IC and IGBTs Driving Common Supply Ground Signal Input for Low-side U Phase Signal Input for Low-side V Phase Signal Input for Low-side W Phase Fault Output Capacitor for Fault Output Duration Time Selection Capacitor (Low-pass Filter) for Short-Current Detection Input ...
Page 4
... Inverter low-side is composed of three IGBTs, freewheeling diodes for each IGBT and one control IC. It has gate drive and protection functions. 2. Inverter power side is composed of four inverter dc-link input terminals and three inverter output terminals. 3. Inverter high-side is composed of three IGBTs, freewheeling diodes and three drive ICs for each IGBT. FSBB30CH60 Rev. C (19) V B(W ) ...
Page 5
... V Isolation Voltage ISO Thermal Resistance Symbol Parameter R Junction to Case Thermal th(j-c)Q Resistance R th(j-c)F Note: 2. For the measurement point of case temperature(T FSBB30CH60 Rev 25°C, Unless Otherwise Specified) J Conditions Applied between P- N Applied between 25° 25°C, Under 1ms Pulse Width 25°C per One Chip ...
Page 6
... C(ON) t OFF t C(OFF Collector-Emitter CES Leakage Current Note and t include the propagation delay time of the internal drive IC OFF For the detailed information, please see Figure 10% I IN(ON) (a) turn-on FSBB30CH60 Rev 25°C, Unless Otherwise Specified) J Conditions 15V I =30A =30A 300V 15V PN CC ...
Page 7
... Control Supply Voltage CC V High-side Bias Voltage BS DV /Dt, Control supply variation Blanking Time for Preventing dead Arm-short f PWM Input Signal PWM V Voltage for Current Sensing SEN FSBB30CH60 Rev 25°C, Unless Otherwise Specified) J Condition V = 15V V - COM CC CC( (UL, VL, WL 15V CC(UH) CC(VH) IN ...
Page 8
... Mechanical Characteristics and Ratings Parameter Mounting Torque Mounting Screw Device Flatness Weight FSBB30CH60 Rev. C Conditions Recommended 0.62N•m Note Figure Figure 5. Flatness Measurement Position 8 Limits Units Min. Typ. Max. 0.51 0.62 0.72 N•m µ +120 - 15. www.fairchildsemi.com ...
Page 9
... Normal operation: IGBT ON and carrying current Under voltage detection (UV BSD b4 : IGBT OFF in spite of control input condition, but there is no fault output signal Under voltage reset (UV ) BSR b6 : Normal operation: IGBT ON and carrying current Figure 7. Under-Voltage Protection (High-side) FSBB30CH60 Rev. C RESET SET UV CCR CCD ...
Page 10
... Fault output timer operation starts: The pulse width of the fault output signal is set by the external capacitor Input “L” : IGBT OFF state Input “H”: IGBT ON state, but during the active period of fault output the IGBT doesn’t turn ON IGBT OFF state Figure 8. Short-Circuit Current Protection (Low-side Operation only) FSBB30CH60 Rev SET RESET ...
Page 11
... The bootstrap resistor (R ) should be 3 times greater than R BS high-side. 3. The ceramic capacitor placed between V -COM should be over 1uF and mounted as close to the pins of the SPM as possible. CC Figure 10. Recommended Bootstrap Operation Circuit and Parameters FSBB30CH60 Rev. C 5V-Line 4.7k Ω 100 Ω ...
Page 12
... P&GND pins is recommended. 11. Relays are used at almost every systems of electrical equipments of home appliances. In these cases, there should be sufficient distance between the CPU and the relays. 12. C should be over 1uF and mounted as close to the pins of the SPM as possible. SPC15 FSBB30CH60 Rev. C 15V line ...
Page 13
... Detailed Package Outline Drawings FSBB30CH60 Rev www.fairchildsemi.com ...
Page 14
... Detailed Package Outline Drawings FSBB30CH60 Rev. C (Continued) 14 www.fairchildsemi.com ...
Page 15
... Detailed Package Outline Drawings FSBB30CH60 Rev. C (Continued) 15 www.fairchildsemi.com ...
Page 16
... PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Preliminary No Identification Needed Obsolete FSBB30CH60 Rev. C IntelliMAX™ POP™ ISOPLANAR™ Power247™ LittleFET™ PowerEdge™ MICROCOUPLER™ PowerSaver™ MicroFET™ ...