E3S-CT11 Omron, E3S-CT11 Datasheet

Page 1

... Diffuse-reflective Vertical * The model number of the Emitter is expressed by adding an "L" to the set model number in the table. Example: E3S-CT11-L 2M, E3S-CT11-L-M1J 0.3M The model number of the receiver is expressed by adding a "D" to the set model number in the table. Example: E3S-CT11-D 2M, E3S-CT11-D-M1J 0.3M Orders for individual Emitters and Receivers are accepted. (Modifications are required for some models.) ...

Page 2

... Note: For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors. Model Quantity 1 set each for Emitter and Re- E39-S61 ceiver (8 Slits total) Model Quantity E39-R1 1 Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor. E39-R2 1 E39-R3 1 E39-R4 1 E39-RS1 1 E39-RS2 1 Enables MSR function. ...

Page 3

... Ratings and Specifications Sensing Through-beam method Horizontal E3S-CT11(-M1J) Model Vertical Item E3S-CT61(-M1J) Sensing distance 30 m Standard sensing Opaque, 15-mm dia. min. object Differential travel Emitter and Receiver: 3 Directional angle to15 Light source Infrared LED (880 nm) (wavelength) Power supply voltage VDC including 10% (p.p) ripple 50 mA max ...

Page 4

... E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) 500 Reflector: E39-R1 300 100 Operating 1 level Distance (m) E3S-C Retro-reflective E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) 400 E39-R1 Reflector Y 300 X 200 100 Distance X (m) 100 200 300 400 Diffuse-reflective E3S-CD@@ (-M1J) 500 Sensing object: White paper 300 ...

Page 5

... Timing charts mode Incident light No incident light Light indicator (Red) Light-ON Output transistor Operate Load (e.g. relay) Reset E3S-CT11(-M1J) E3S-CT61(-M1J) Incident light No incident light E3S-CR11(-M1J) Light indicator (Red) E3S-CR61(-M1J) Dark-ON Output transistor E3S-CD11(-M1J) Operate E3S-CD12(-M1J) Load (e ...

Page 6

... not possible to mount the E3S-C so that the sensing objects will be in the direction the mechanical axis, move the E3S-C upwards, downwards, to the left the right and secure the E3S the center of the range where the light indicator will be lit, at which time make sure that the stability indicator is lit ...

Page 7

... E3S-C was dipped in all the above oils at a temperature for 240 hours. 2. When using the E3S place where an oil other than the ones listed above is sprayed on the E3S-C, refer to the above kinematic viscosity and ph values. The location may be suitable for the E3S-C if ...

Page 8

... Dimensions Sensors Through-beam (Horizontal) E3S-CT11(-M1J) Emitter: E3S-CT@@-L Receiver: E3S-CT@@-D Lens (17 11) Optical axis 2 9 Two, M4 1.5 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm insulator diameter: 1 ...

Page 9

... Stability indicator (green) 4.2 9.2 8.3 4.2 Stainless steel (SUS304) 6.2 38.2 2 20.8 25.4 E3S-C Pre-wired Connector (-M1J) M12 1 4-dia. vinyl-insulated round cable with 3 conductors 2 (Conductor cross section: 0.2 mm (AWG24), Insulator diameter: 1.2 mm), Standard length 20.4 Mounting Holes Two 9.2 25 ...

Page 10

... A 0.2 6.2 11.8 3.8 E3S-C Pre-wired Connector (-M1J) M12 1 4-dia. vinyl-insulated round cable Standard length: 300 mm 4-dia. vinyl-insulated round cable with 3 conductors 2 (Conductor cross section: 0.2 mm (AWG24), Insulator diameter: 1.2 mm), Standard length 20.4 ...

Page 11

... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...