HEDS-8933 Avago Technologies US Inc., HEDS-8933 Datasheet - Page 4

• Manufacturer Part Number: HEDS-8933
• Description: TOOL ALIGNMENT AEAS-7000 SERIES
• Manufacturer: Avago Technologies US Inc.

Specifications of HEDS-8933

• Accessory Type: Mechanical Alignment Tool
• Product: Tools & Accessories
• Size / Dimension: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: AEAS-7000 Series
• For Use With: 516-2181 - IC ENCODER ABS 16BIT SERIALAEAS-7000-1GSD0 - IC ENCODER ABS 13BIT SERIAL 85C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Absolute Maximum Ratings
Notes:
1. Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is stress rating only
2. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Recommended Operating Condition
Notes:
1. Voltage ripple of supply voltage, Vripple, should be within 100mVpp or less for improved accuracy.
Electrical Characteristics
Electrical Characteristics over Recommended Operating Range, typical at TA=25 °C and VD = 5V
Notes:
1. LSB accuracy will also depend on mechanical precision of the shaft, bearings, hub etc.
2. Accuracy would be influenced by installation control and the bearing and shaft type being used.
3. Other test conditions to determine accuracy are briefly listed as follows:
4
Parameter
DC Supply Voltage
Input Voltage
Output Voltage
Relative Air Humidity (non-condensing)
Operating Temperature
Storage Temperature
Parameter
DC Supply Voltage
Operating Temperature
Input High Level
Input Low Level
Parameter
Digital Input-Pull Down Current
Digital Input-Pull Up Current
Digital Ouput-H-Level
Digital Ouput-L-Level
SCL Clock Frequency
Duty Cycle SCL Clock
Signal frequency of A0, A09
Total Operating Current
Accuracy within one revolution
and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification
is not implied.
Final accuracy of the encoder module is dependent on the precision of the total assembly.
(a) At nominal radial, tangential and gap position
(b) On dual preloaded bearing with absolute assembly total runout of not exceeding 0.01 mm TIR
(c) Both VDD & VDDA RC filters placed not more than 20mm from header pins
1, 2, 3
1, 2
Symbol
I
I
I
V
V
f
T
f
Symbol
VD
T
V
V
total
pd
pu
SCL
A0
LH
OH
OL
A
IH
LH
, f
A09
RH
Symbol
VD
V
V
T
T
A
S
in
out
Condition
I
I
RPM =80
T
f
V
Min.
+ 4.5
- 25
0.7*VD
0
OH
OL
Values
SCL
LH
ripple
= - 2 mA
= 2 mA
= H/(L+H)
= 5MHz
<50mVpp
+ 5.0
25
Typ.
Limits
-0.3 to + 6.0
-0.3 to +VD +0.3
-0.3 to +VD +0.3
85
- 25 to +85
- 35 to +85
Min
-20
30
VD -0.5 V
0
0.4
Values
Max.
0.3*VD
+5.5
+85
VD
25
±2 bit
Typical
Units
V
°C
V
V
Max
-5
160
0.5
16
0.6
250
VD
Units
%
°C
°C
V
V
V
Notes
1
Units
mA
µA
µA
MHz
kHz
V
V