MT5600BA-V92-EU Multi-Tech Systems, MT5600BA-V92-EU Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
MT5600BA-V92-EU
Manufacturer Part Number
MT5600BA-V92-EU
Description
MODEM V.92 DATA/FAX WORLD
Manufacturer
Multi-Tech Systems
Series
MultiModem® IIr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MT5656ZDX-EU.pdf
(55 pages)
3.MT5600BA-V92-NPS.pdf
(2 pages)
4.MT5600BA-V92-NPS.pdf
(8 pages)
5.MT5600BA-V92-NPS.pdf
(58 pages)
Specifications of MT5600BA-V92-EU
Data Format
V.92
Interface
RS-232
Voltage - Supply
9 V ~ 12 V
Mounting Type
Desktop
Package / Case
9.0" L x 6.2" W x 1.4" H (229mm x 158mm x 36mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1058
Command:
Values:
Default:
Description:
Command:
Values:
Default:
Description:
Command:
Values:
Default:
Description:
Command:
Values:
Default:
Description:
Command:
Values:
Defaults:
Description:
Command:
Values:
Default:
Description:
Multi-Tech Systems, Inc. AT Commands Reference Guide (S000273G)
&Gn V.22bis Guard Tone Control
&En Modem-Initiated Flow Control
&En V.42bis Data Compression
&Fn Load Factory Settings
&Kn Flow Control Selection
&Mn Communications Mode
Note:
n = 3, 4, or 5
4
&E3
&E4
&E5
Note:
Note:
n = 14 or 15
15
&E14 V.42bis data compression disabled.
&E15 V.42bis data compression enabled.
Note:
n = 0 or 1
None
&F0
&F1
Note:
n = 0, 1, or2
Varies by country
&G0 Disables guard tone.
&G1 Sets guard tone to 550 Hz.
&G2 Sets guard tone to 1800 Hz.
Note:
n = 0, 3, 4, 5, or6
3 (data modem mode)
6 (fax modem and voice modes)
&K0
&K3
&K4
&K5
&K6
Note: See also the &E command
n = 0–3
0
This command determines the DTR operating mode. The modem treats the &M command
as a subset of the &Q command.
&M0 Selects direct asynchronous operation. Command sequence &M0\N0 selects
&M1 Selects synchronous connect mode with asynchronous offline command mode.
&M2
&M3 Selects synchronous connect mode. This mode allows DTR to act as a talk/data
For use with MT5600BA and MT5600BR only.
For use with MT5600BA and MT5600BR only.
Flow control disabled.
CTS/RTS hardware flow control.
XON/XOFF software flow control.
See also the L5 and &K commands.
This command controls only V.42bis data compression, whereas the %C command
controls both V.42bis and MNP-5 data compression. The command in effect is the
one last entered. See also the L5 command.
Loads factory configuration 0.
Loads factory configuration 1.
See also the Z, L5, and &V commands.
The &G command is not used in North America, and may not be permitted in some
countries.
Disables flow control.
Enables CTS/RTS hardware flow control.
Enables XON/XOFF software flow control.
Enables transparent XON/XOFF flow control.
Enables both CTS/RTS and XON/XOFF flow control.
normal buffered mode, but command sequence \N0&M0 selects direct mode. This
is because the \N0 command is analogous to the &Q6 command.
Note:
connect mode with asynchronous offline command mode.
Same as &M1 except that &M2 enables DTR dialing of directory slot 0. The modem
disconnects if DTR is low for more than the period stored in S25.
switch. A call is manually initiated while DTR is inactive; when it becomes active,
the handshake proceeds in originate or answer mode according to S14 bit 7.
For use with the MT5656ZDX and MT5656ZDX-V only. Selects synchronous
Chapter 2 – AT Commands
9