AFBR-5715PZ Avago Technologies US Inc., AFBR-5715PZ Datasheet - Page 8

• Manufacturer Part Number: AFBR-5715PZ
• Description: Fiber Optic Transmitters, Receivers, Transceivers Transceiver
• Manufacturer: Avago Technologies US Inc.
• Type: TX/RXr
• Series: -r

Specifications of AFBR-5715PZ

• Function: Designed for those applications requiring DMI features.
• Product: Transceiver
• Data Rate: 1.25 GBd
• Wavelength: 850 nm
• Maximum Rise Time: 0.26 ns/0.22 ns (Typ)
• Maximum Fall Time: 0.26 ns/0.22 ns (Typ)
• Pulse Width Distortion: 0.227 ns (Max)/0.266 ns (Max)
• Operating Supply Voltage: 3.135 V to 3.465 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Package / Case: SFP
• Mounting Type: SFP
• Voltage - Supply: 3.135 V ~ 3.465 V
• Connector Type: LC Duplex
• Applications: Ethernet
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 1250MBd
• Optical Rise Time: 0.26/0.22ns
• Optical Fall Time: 0.26/0.22ns
• Jitter: 0.227/0.266ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 850nm
• Package Type: SFP
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.465V
• Operating Temp Range: -10C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Package: 20SFP
• Rise Time: 0.26/0.22(Typ) ns
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Multimode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 2. Pin Description
Notes:
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7K – 10 K resistor on the host board to a supply
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 K resistor.
3. Mod-Def 0,1,2. These are the module defi nition pins. They should be pulled up with a 4.7-10 K resistor on the host board to a supply less
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K – 10 K resistor on the host board to a
5. RD-/+: These are the diff erential receiver outputs. They are AC coupled 100  diff erential lines which should be terminated with 100  diff erential
6. VccR and VccT are the receiver and transmitter power supplies. They are defi ned as 3.135 – 3.465 V at the SFP connector pin. The in-rush current
7. TD-/+: These are the diff erential transmitter inputs. They are AC coupled diff erential lines with 100  diff erential termination inside the module.
8
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the
output will be pulled to < 0.8 V.
than VccT +0.3 V or VccR+0.3 V.
supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defi ned by
the standard in use). Low indicates normal operatio0n. In the low state, the output will be pulled to < 0.8 V.
at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines
must be between 370 and 2000 mV diff erential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv diff erential.
will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept diff erential swings of 500 – 2400
mV (250 – 1200 mV single ended). However, the applicable recommended diff erential voltage swing is found in Table 5.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
Low (0 – 0.8 V):
Between (0.8 V and 2.0 V):
High (2.0 – 3.465 V):
Open:
Name
VeeT
TX Fault
TX Disable
MOD-DEF2
MOD-DEF1
MOD-DEF0
Rate Selection
LOS
VeeR
VeeR
VeeR
RD-
RD+
VeeR
VccR
VccT
VeeT
TD+
TD-
VeeT
Function/Description
Transmitter Ground
Transmitter Fault Indication
Transmitter Disable - Module disables on high or open
Module Defi nition 2 - Two wire serial ID interface
Module Defi nition 1 - Two wire serial ID interface
Module Defi nition 0 - Grounded in module
Not Connected
Loss of Signal
Receiver Ground
Receiver Ground
Receiver Ground
Inverse Received Data Out
Received Data Out
Reciver Ground
Receiver Power -3.3 V ±5%
Transmitter Power -3.3 V ±5%
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
Transmitter on
Undefi ned
Transmitter Disabled
Transmitter Disabled
Engagement
Order(insertion)
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
Notes
1
2
3
3
3
4
5
5
6
6
7
7