EE-SY672 Omron, EE-SY672 Datasheet
![Photomicrosensors REFL LIGHT-ON/DRK-ON](/photos/15/87/158718/ee-sy671_2f_sml.jpg)
EE-SY672
Specifications of EE-SY672
Available stocks
Related parts for EE-SY672
EE-SY672 Summary of contents
Page 1
... Appearance Sensing method Sensing distance (white paper Reflective with reflection factor of 90%) *The Light-ON/Dark-ON models can be used as Light-ON models when the L terminal and positive (+) terminal are connected. To use them as Dark-ON models do not connect these terminals. Output configuration Weight Part number Light-ON/Dark-ON* Approx. 3.5 g EE-SY671 EE-SY672 ...
Page 2
... Sensing face: fluorescent light: 1,500 x max. IP50 - ( 131 176 F) 45% to 85% 35% to 95% Destruction 2,000 Hz, 1.5-mm double amplitude for 2 hrs each and Z directions 2 Destruction: 500 m/s (approx. 50G) for 3 times each and Z directions max. (0.3 mm min.) EE-SY671/672 EE-SY672 ) with a residual voltage of 0.4 V max. ...
Page 3
... EE-SY671/672 Engineering Data OPERATING RANGE (TYPICAL) Sensing object: White paper 2 ( reflection factor: 90 Operates Releases Sensing position X (mm) SENSING DISTANCE VS. OBJECT AREA (TYPICAL) Sensing object: White paper (reflection factor: 90 With max. sensitivity 2 2 Sensing area ( Operation INTERNAL/EXTERNAL OUTPUT CIRCUIT DIAGRAM Light-ON/Dark-ON Opera- ...
Page 4
... Sensing face position (back) 25.4 (1.00) 6.95 (0.27) Sensitivity 19 (0.75) adjustor 6.35 13.4 (0.53) (0.25) Two, 3.8 dia. holed 13.2 (0.52) 5.5 (0.22) 0.3 (0.01) (1) (2) (3) (4) 2.54 0.7 (0.10) (0.03) EE-SY671/672 Incident Interrupted ON OFF ON OFF Operates Releases H L Terminal Arrangement ( ( (3) OUT OUTPUT ...
Page 5
... EE-SY671/672 EE-SY672 16.7 (0.66) 25 (0.98) 31.2 (1.23) 8.3 (0.33) 6.2 (0.24) Indicator window EE-1001 CONNECTOR 13.0 (0.51) 2.54 0.15 4.0 (0.16) 10.8 (0.43) 6.0 (0.24) EE-1006 CONNECTOR WITH CABLE 0.6 (0.02) 16.2 (0.64) (1) 11.8 (2) (0.46) (3) (4) 2.54 (0.10) 5.3 (0.21) Two, 3.2 dia. holes 19 (0 ...
Page 6
... Autotransformer Power source Power source Insulated transformer 3. Set the sensitivity adjuster at the center (point C) between points A and B. Points A and B will be very close if the sen- sor is influenced by excessive light reflected by the back- ground object. If this is true, take the following preventative measures: Make a large enough distance between the sensor and the background object ...
Page 7
... A). 2. Set the sensitivity adjuster at the center (point C) between points A and B (the point where the sensitivity is maximum). NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4. ...