PIC-USB-STK Olimex Ltd., PIC-USB-STK Datasheet
PIC-USB-STK
Specifications of PIC-USB-STK
Related parts for PIC-USB-STK
PIC-USB-STK Summary of contents
Page 1
... PIC-USB-STK development board All boards produced by Olimex are ROHS compliant Copyright(c) 2008, OLIMEX Ltd, All rights reserved Users Manual Rev.A, March 2008 _________ ...
Page 2
... INTRODUCTION: PIC-USB-STK is starterkit which allow you to explore all capabilities of PIC18F4550 and the Microchip's USB firmware. The software examples include: USB HID mouse which allow you to move the mouse cursor with the four buttons on the board, USB Mass storage device on SD-MMC card simple ...
Page 3
Software: BOARD LAYOUT: the programmer to your target board, you should first connect the programmer to your computer and open MPLAB. There, first from menu Configure – Select Device – choose the microcontroller you are about to program, then from ...
Page 4
SCHEMATIC: ...
Page 5
... PROCESSOR FEATURES: Here are listed PIC18F4550 main features: - CPU clock MHz; - FLASH 32 KBytes; - RAM 2048 Bytes; - EEPROM 256 Bytes; - USB 2.0 Full Speed (12 Mb/ I/O ports; - ADC 10 bit, 13 channels; - SPI x1; - I2C x1; - UART x1; - SPP x1; - CCP/PWM x1; - Comparators x2; - Timers 8/16bit x1/3; - power supply 2.0-5.5V; ...
Page 6
Block diagram: ...
Page 7
MEMORY MAP: POWER SUPPLY CIRCUIT: ...
Page 8
... USB connector. Current consumption from power supply is typical around 70mA with shipped PIC-USB-STK demo code. RESET CIRCUIT: PIC-USB-STK reset circuit is made with 10k pull-up resistor and RST button connected to GND. CLOCK CIRCUIT: Quartz crystal Q1-20Mhz is connected to PIC18F4550 OSC1and OSC2 pins. ...
Page 9
... ProgramClock PB6 line and the result will be not predictable Default state - closed The B3_E jumper connects Button 3 with PB7/PGD pin of PIC18F4550. In debug mode please do not press Button 3 as this will corrupt ProgramData PB7 and the result will be not predictable. Default state - closed The EXTernal/USB jumper defines the power source which supply the board ...
Page 10
INPUT/OUTPUT: Trimmer pot: Buttons: LEDs: AUDIO: Trimmer potentiometer 10K connected to RA0/AN0 four user buttons are available: Button1 connected to RB5 with pullup, when the button is pressed the RB5 is read as 0, otherwise as 1 Button2 connected to ...
Page 11
EXTERNAL CONNECTOR DESCRIPTION: PWR_JACK: Pin # Signal Name 1 Power Input 2 Polarity doesn’t matter as there is diode bridge. USB: Pin # Signal Name 1 +5V_USB GND This is standard USB Type B connector. ...
Page 12
HEADPHONE: Pin # Signal Name 1-L Audio Left OUT 2-C GND 3-R Audio Right OUT This is 3.5 mm Audio jack female connector and work with most standard 3.5 mm jack headphones. Note the signal is Mono i.e. Left and ...
Page 13
... GND 4 PGD 5 PGC 6 Not Connected This is standard ICSP connector used in all Olimex’s board. The connector is CI33 type made by Cvilux Inc. Taiwan. If you are not using Olimex ICD2 but Microchip you will need PIC-ICSP cross-cable Extension: Pin # Signal Name VIN 3 GND 4 3 ...
Page 14
MECHANICAL DIMENSIONS: ...
Page 15
... AVAILABLE DEMO SOFTWARE: PIC-USB-STK is shipping with pre-programmed Microchip’s USB bootloader and demo code. The Bootloader allow HEX files to be loaded in the PIC via USB interface using the free dowloadable software from Microchip’s web: http://ww1.microchip.com/downloads/en/DeviceDoc/MCHPFSUSB_Setup_v1.3.exe How to use the bootloader document is available at: http://ww1 ...
Page 16
ORDER CODE: How to order? You can order to us directly or by any of our distributors. Check our web All boards produced by Olimex are ROHS compliant Revision history: REV.A - create March 2008 www.olimex.com/dev for more info. ...
Page 17
... This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such ...