ERT-J1VR103J Panasonic, ERT-J1VR103J Datasheet
![Thermistors - NTC 10K OHM 5%](/photos/16/24/162484/ertj_sml.jpg)
ERT-J1VR103J
Specifications of ERT-J1VR103J
Available stocks
Related parts for ERT-J1VR103J
ERT-J1VR103J Summary of contents
Page 1
... Multilayer Chip NTC Thermistors ERTJ Type: The miniaturized Multilayer Chip NTC Thermistors (ERTJ) are specially designed for surface mounting capacitors. n Features l High reliable multilayer / monolithic structure l Superior heat resistance to reflow soldering and excellent solderability l Wide ranges of operating temperature (Ð40 to 125 ¡C) ...
Page 2
Dimensions in mm (not to scale) n Packaging Specifications l Standard Packing Quantity Style Paper taping Thickness Size Code JZ (0201) 0.3 mm Pitch 2 mm: 15000 pcs./reel J0 (0402) 0.5 mm Pitch 2 mm: 10000 pcs./reel J1 (0603) ...
Page 3
... NTC Thermistors (Chip Type) 0201 Type approximately 1mW / ¡ ERTJ11V ERTJ11G (4700 K) (3435 K) ] typical typical 59.797 20.238 41.298 15.292 28.758 11.669 20.267 8.988 14.428 6.984 10.368 5.472 7.519 4 ...
Page 4
... ERTJ0ER4721 ERTJ0ER6821 ERTJ0ER1031 ERTJ0ER1531 ERTJ0ER2231 ERTJ0ER3331 ERTJ0EP4731 ERTJ0EV4731 ERTJ0EV6831 ERTJ0EV1041 ERTJ0EV1541 ERTJ0EV2241 ERTJ0EV3341 ERTJ0EV4741 ERTJ1VA2201 ERTJ1VA3301 ERTJ1VA4001 ERTJ1VA4701 ERTJ1VA6801 ERTJ1VA1011 ERTJ1VT1021 ERTJ1VT1521 ERTJ1VT2021 ERTJ1VT2221 ERTJ1VT3021 ERTJ1VT3321 J1 ERTJ1VT4721 (0603) ERTJ1VR3321 ERTJ1VR4721 ERTJ1VR6821 ERTJ1VR1031 ERTJ1VR1531 ERTJ1VR2231 ERTJ1VR3331 ERTJ1VR4731 ERTJ1VR6831 ERTJ1VP4731 ERTJ1VV4731 ERTJ1VV6831 ...
Page 5
Multilayer Chip NTC Thermistors Safety Precautions The Multilayer Chip NTC Thermistors (hereafter referred to as ÒThermistorsÓ) are intended for general consumer-type electronic (audiovisual, household, office, information & communication )equipment important to understand the features and specifications before making ...
Page 6
Recommended Amount of Solder: As shown in Fig.2 Excess amounts of solder may cause large mechanical stresses to the Thermistors/components. Fig.2 Recommended Amount of Solder 2.3 Component Layout When placing/mounting the Thermistors/components near an area which is apt to ...
Page 7
Soldering Flux and Solder (1) Soldering Flux: l The content of halogen in the soldering flux should be 0.2 wt% or less. l Rosin-based and non-activated soldering flux is recommended. (2) Water soluble type Soldering Flux: In case of ...
Page 8
Hand Soldering In hand soldering of the Thermistors, a large temperature gradient between the Thermistors and the tip of soldering iron may cause electrical failures and mechanical damages such as cracking or breaking of the device. The soldering should ...