PVZ3A105C01R00 Murata, PVZ3A105C01R00 Datasheet - Page 25
![Trimmer Resistors - SMD 1M OHM SMD 3MM](/photos/16/51/165154/130p01_sml.jpg)
PVZ3A105C01R00
Manufacturer Part Number
PVZ3A105C01R00
Description
Trimmer Resistors - SMD 1M OHM SMD 3MM
Manufacturer
Murata
Series
PVZ3Ar
Specifications of PVZ3A105C01R00
Resistance
1 MOhms
Power Rating
0.1 Watt (1/10 Watt)
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Dimensions
3.1 mm W x 3.2 mm L x 1.85 mm H
Product
Single-Turn Trimmer Potentiometers
Termination Style
SMD/SMT
Tolerance
30 %
Number Of Turns
1
Taper
Linear
Temperature Coefficient
+/- 500 PPM / C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PVZ3A105C01R00
Manufacturer:
MURATA
Quantity:
240 000
Part Number:
PVZ3A105C01R00
Manufacturer:
MURATA/村田
Quantity:
20 000
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
1. Soldering
(1) Can be soldered by reflow soldering method, flow
(2) Use our standard land dimension. Excessive land
(3) Soldering condition
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
Notice (Soldering and Mounting)
soldering method, and soldering iron.
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive temperature,
the trimmer potentiometer may deviate from the
specified characteristics.
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the
dimension of land pattern used should be Murata's
standard land pattern at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(5) The soldering iron should not come in contact
(1) Do not apply excessive force, preferably 9.8N
(2) Do not warp and/or bend PC board to prevent
(3) In chip placers, the recommended size of the
Isopropyl alcohol and Ethyl alcohol are available
materials for cleaning.
For other materials, please consult with a Murata
factory representative prior to using.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
max. (Ref. 1kgf) when the trimmer potentiometer
is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia.
PVM4 Series Notice
R50E.pdf
23
11.1.17
4