PVZ3A105C01R00 Murata, PVZ3A105C01R00 Datasheet - Page 48
![Trimmer Resistors - SMD 1M OHM SMD 3MM](/photos/16/51/165154/130p01_sml.jpg)
PVZ3A105C01R00
Manufacturer Part Number
PVZ3A105C01R00
Description
Trimmer Resistors - SMD 1M OHM SMD 3MM
Manufacturer
Murata
Series
PVZ3Ar
Specifications of PVZ3A105C01R00
Resistance
1 MOhms
Power Rating
0.1 Watt (1/10 Watt)
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Dimensions
3.1 mm W x 3.2 mm L x 1.85 mm H
Product
Single-Turn Trimmer Potentiometers
Termination Style
SMD/SMT
Tolerance
30 %
Number Of Turns
1
Taper
Linear
Temperature Coefficient
+/- 500 PPM / C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PVZ3A105C01R00
Manufacturer:
MURATA
Quantity:
240 000
Part Number:
PVZ3A105C01R00
Manufacturer:
MURATA/村田
Quantity:
20 000
7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
46
No.
The following describes trimmer potentiometer testing conducted by Murata Manufacturing Co., Ltd. in accordance with MIL-R-22097 (Military specification
for variable resistors, non-wirewound) and MIL-STD-202 (Test methods for electronic and electrical component parts).
SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods
1
2
3
4
5
Total Resistance
Residual Resistance
Contact Resistance
Variation
Temperature Coefficient of
Resistance
Voltage Setting
Stability
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
TCR=
Measure total resistance between the resistance element and terminals (#1 and #3) with the contact arm positioned
against a stop. The positioning of the contact arm and terminal should be the same for subsequent total resistance
measurements on the same device. Use the test voltage specified in Table 1 for total resistance measurements.
This voltage should be used for all subsequent total resistance measurements.
Position the contact arm at the extreme counterclockwise limit of mechanical travel and measure the resistance
between the contact arm and the corresponding end terminal. Then, position the contact arm at the extreme clock-
wise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end ter-
minal. During this test, take suitable precautions to ensure that the rated current of the resistance element is not
exceeded.
Contact resistance variation should be measured with the measuring circuit shown in Figure 1, or its equivalent. The
adjustment rotor (screw) should be rotated in both directions through 90% of the actual effective-electrical rotational
angle (number of turns) for a total of 6 cycles. Only the last 3 cycles should count in determining whether or not a
contact resistance variation is observed at least twice in the same location, exclusive of the roll-on or roll-off points
where the contact arm moves from the termination, on or off, the resistance element. The rate of rotation of the
adjustment rotor (screw) should be such that the adjustment rotor (screw) completes 1 cycle for 5 seconds minimum
to 2 minutes maximum. The test current used should follow the value given in Table 2 unless otherwise limited by
power rating.
The trimmer potentiometer should be subjected to each of the following temperatures (see Table 3) for 30-45 min-
utes. Temperature coefficient of resistance should be applied to the following formula.
Note*: Reference temperature
The wiper should be set at approximately 40% of the actual effective-electrical rotational angle (number of turns). An
adequate DC test potential should be applied between terminal #1 and terminal #3. The voltage between terminal #1
and terminal #3, and the voltage between terminal #1 and terminal #2, should be measured and applied to the
following formula.
Voltage setting stability=
e : Before test
e' : After test
Standard Total Resistance
Total Resistance,
Temperature ( C)
(The voltage between terminal #1 and terminal #2)
(The voltage between terminal #1 and terminal #2)
Nominal (ohm)
Table 1: Total resistance test voltage
100kFR
100FR
10kFR
Sequence
10VR
1kFR
R
200kVR
T
T
R
R
100FR
500VR
50kVR
Table 2: Test current for CRV
1
1MVR
2MVR
R
1
2
1
2
1kVR
2kVR
(T
R (ohm)
2
V100
V1k
V10k
V100k
: Reference temperature in degrees celsius
: Test temperature in degrees celsius
: Resistance at reference temperature ohm
: Resistance at test temperature in ohm
– R
2
R
– T
V100
F500
F1k
F2k
F50k
F200k
F1M
F2M
1
1
)
Z 10
+25
(
Maximum Test
1*
—
6
e'
E
Voltage (V)
(ppm/ C)
– —
100.0
10.0
30.0
1.0
3.0
E
e
Table 3: Test temperatures
Test Current
-15
)
2
Z100 (%)
200 A
100 A
20mA
10mA
50 A
30 A
4mA
2mA
1mA
Min. operating
Temperature
3
Test Methods
Constant Current Source
(Test current shown in Table 2)
+25
4*
#1
+65
Rx : Trimmer Potentiometer
Oscilloscope bandwidth :100Hz to 50kHz
Figure 1: CRV measuring circuit
5
Max. operating
Temperature
#1
e
Resistance
Proofread
#2
Rx
6
Figure 2
Continued on the following page.
E
#3
#2
AC
Amplifier
#3
Oscilloscope
R50E.pdf
11.1.17