EE-1001 Omron, EE-1001 Datasheet - Page 82

• Manufacturer Part Number: EE-1001
• Description: Sensor Hardware & Accessories 4 Pin Connector For PMS
• Manufacturer: Omron

Specifications of EE-1001

• Product: Connector
• Connector Mounting: Cable
• Gender: Female
• Connector Type: Sensor
• Terminal Type: Solder Lug
• Accessory Type: Connector
• Contact Material: Phosphor Bronze
• Contact Termination: Solder
• Rohs Compliant: Yes
• For Use With: EE-SX67x, EE-SX47x, EE-SY67x, EE-SPY31x/41x, EE-SPX303/403, EE-SPW311/411 Sensor Models
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: Omron Photosensors
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

80
Motor features and options
Command inputs accepted
Application suggestions
Product power range
Sample capabilities
±10 V analog signal
Stand-alone servo
pulse train signal
Position control
position control
with integrated
Voltage supply
Motor features
Motion control
Drive features
PLC modules
PLC modules
PC software
Approvals
Networks
• Mechatrolink II Network support
• High resolution control
• Ultra-small package
• High performance 32-bit micro-processor
• Built-in keypad and display
• Auto-tuning automatically adjusts the control system gain
• Low rotor inertia design yields a high power rate
• Reduced cogging torque for smooth motor rotation
30 W to 15 kW
100/115 VAC (single phase) or
200/230 VAC (single phase and three phase)
Capable of handling analog speed, analog torque, and pulse-train
input all in one single drive
Standard features include 1000, 1500 and 3000 RPM rated speed
motors, high-resolution serial incremental encoders up to 17-bit.
Options include 17-bit absolute encoders, holding brakes,
keyways and water resistant slim profile motors
UL, cUL CE, TUV
Conveyors; Pick and place machines; Lathes; Winding; Point-to-
point positioning; Indexing; Cut to length; Packaging and filling
machines
W-Series is field upgradable to integrate position control and
DeviceNet connectivity by adding the R88A-NCW152-DRT,
DeviceNet Option Unit
Note: Only for amplifiers with firmware version 14 or later (1-axis)
CS1W-MC221 (2-axis); CS1W-MC421 (4-axis);
C200H-MC221 (2-axis); CS1W-MCH71 (30-axis);
CJ1W-MCH71 (30-axis)
CS1W-NC1 3 (1-axis); CS1W-NC2 3 (2-axis);
CS1W-NC4 3 (4-axis)
CJ1W-NC1 3 (1-axis); CJ1W-NC2 3 (2-axis);
CJ1W-NC4 3 (4-axis); CJ1W-NCFH (16-axis)
C200HW-NC113 (1-axis); C200HW-NC213 (2-axis)
C200HW-NC413 (4-axis)
WMon config/monitor; CX-Motion programming for MC; CX-
Position config/monitor for CS1/CJ1-NC;
NCT config/monitor for C200HW-NC;
MC-MIEL for CS1W-MCH71
Point-to-point positioning; Speed control; Electronic gearing;
Linear, circular, and helical interpolation
Mechatrolink II Interface FNY-NS115
Mechatrolink II Cables FNY-W6003-XX
Mechatrolink II Terminator FNY-W6002
Note: WN-Series has built-in Mechatrolink II Interface
according to machine characteristics
at low speeds
Servo Motors & Drives
W-Series/WN-Series
• Simple to use and easy to set-up using on-board selector
• Auto-tuning available to automatically adjust servo gain
• 7-segment alarm display helps in troubleshooting
• Pulse input
• Low rotor inertia design yields a high power rate
• Reduced cogging torque for smooth motor rotation
30 W to 750 W
100/115 VAC (single phase); 200/230 VAC (single phase);
200/230 VAC (three phase for 750 W only)
Capable of handling pulse-train inputs
Motor rated speed is 3000 RPM and continuous torques are
between 0.09 to 2.39 Nm; Pre-quadrature encoder resolution is
2000 ppr; Holding brake option available
UL, cUL, CE
Conveying; Pick and place; Point-to-point positioning; Indexing;
Cut to length; Packaging
Not yet available
Not applicable
CS1W-NC1 3 (1-axis); CS1W-NC2 3 (2-axis);
CS1W-NC4 3 (4-axis)
CJ1W-NC1 3 (1-axis); CJ1W-NC2 3 (2-axis);
CJ1W-NC4 3 (4-axis)
C200HW-NC113 (1-axis); C200HW-NC213 (2-axis)
C200HW-NC413 (4-axis)
WMon V2.0 config/monitor;
CX-Position config/monitor for CS1/CJ1-NC;
NCT config/monitor for C200HW-NC
Point-to-point positioning; Speed control; Electronic gearing;
Linear interpolation
–
switches and DIP switches
parameters to load characteristics
at low speeds
SMARTSTEP Servo