TLF14CBH4730R2K1 Taiyo Yuden, TLF14CBH4730R2K1 Datasheet - Page 11

• Manufacturer Part Number: TLF14CBH4730R2K1
• Description: CHOKE COMMON MODE 47000UH
• Manufacturer: Taiyo Yuden
• Series: TLF14CBHr

Specifications of TLF14CBH4730R2K1

• Current: 200mA
• Inductance: 47mH
• Dc Resistance (dcr): 3.6 Ohm Max
• Filter Type: Common Mode - 2 Line Array
• Package / Case: 0.906" L x 0.867" W x 0.690" H (23.00mm x 22.00mm x 17.50mm)
• Mounting Type: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Impedance: -
• Other names: 587-2829

le0104fi01_reli-RP7
■
CAL Type, LH Type, FB Type, FL Type, LA Type
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
Precautions
Precautions
Precautions
Precautions
Precautions
Precautions
Precautions
1. Circuit Design
2. PCB Design
3. Considerations for automatic placement
4. Soldering
5. Cleaning
6. Handling
7. Storage conditions
Technical
consider-
Technical
consider-
Technical
consider-
Technical
consider-
Technical
consider-
Technical
consider-
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PRECAUTIONS
ations
ations
ations
ations
ations
ations
◆Operating environment
◆Design
◆Design
◆Adjustment of mounting machine
◆Adjustment of mounting machine
◆Wave soldering
◆Lead free soldering
◆Reflow soldering
◆Lead free soldering
◆Cleaning conditions
◆Cleaning conditions
◆Handling
◆Mechanical considerations
◆Packing
◆Handling
◆Mechanical considerations
◆Packing
◆Storage
◆Storage
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc
1. As for reflow soldering, please contact our sales staff.
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
1. CAL type, LH type, LA Type
1. CAL type, LH type, LA Type
1. Keep the inductors away from all magnets and magnetic objects.
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
1. Please do not give the inductors any excessive mechanical shocks.
1. There is a case that a characteristic varies with magnetic influence.
1. There is a case to be damaged by a mechanical shock.
2. LH type
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・ The soldering iron should not directly touch the inductor.
・ Ambient temperature 0～40℃
・Humidity
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
sufficiently.
Recommended conditions for using a soldering iron:
the products.
be controlled.
Recommended conditions
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
taping/packaging materials may take place.
Please do not do cleaning by a supersonic wave.
If washing by supersonic waves, supersonic waves may deform products.
If inductors are dropped onto the floor or a hard surface they should not be used.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
There is a case to be broken by a fall.
Below 70% RH
1 1
le0104fi01_reli_e-01