LPC2146FBD64,557 NXP Semiconductors, LPC2146FBD64,557 Datasheet - Page 16

• Manufacturer Part Number: LPC2146FBD64,557
• Description: IC ARM7 MCU FLASH 256K 64LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2146FBD64,557

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 45
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 14x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

NXP Semiconductors
LPC2141_42_44_46_48_4
Product data sheet
6.7.1 Features
6.8.1 Features
6.9.1 Features
6.7 Fast general purpose parallel I/O (GPIO)
6.8 10-bit ADC
6.9 10-bit DAC
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
LPC2141/42/44/46/48 introduce accelerated GPIO functions over prior LPC2000 devices:
The LPC2141/42 contain one and the LPC2144/46/48 contain two analog to digital
converters. These converters are single 10-bit successive approximation analog to digital
converters. While ADC0 has six channels, ADC1 has eight channels. Therefore, total
number of available ADC inputs for LPC2141/42 is 6 and for LPC2144/46/48 is 14.
The DAC enables the LPC2141/42/44/46/48 to generate a variable analog output. The
maximum DAC output voltage is the VREF voltage.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
GPIO registers are relocated to the ARM local bus for the fastest possible I/O timing.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All GPIO registers are byte addressable.
Entire port value can be written in one instruction.
Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
10 bit successive approximation analog to digital converter.
Measurement range of 0 V to VREF (2.0 V
Each converter capable of performing more than 400000 10-bit samples per second.
Every analog input has a dedicated result register to reduce interrupt overhead.
Burst conversion mode for single or multiple inputs.
Optional conversion on transition on input pin or timer match signal.
Global Start command for both converters (LPC2142/44/46/48 only).
10-bit DAC.
Buffered output.
Power-down mode available.
Rev. 04 — 17 November 2008
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
VREF
V
DDA
).
© NXP B.V. 2008. All rights reserved.
16 of 40