PC28F640J3D75E NUMONYX, PC28F640J3D75E Datasheet - Page 9
![IC FLASH 64MBIT 75NS 64EZBGA](/photos/7/24/72451/pc28f640j3d75_s_l8zt_sml.jpg)
PC28F640J3D75E
Manufacturer Part Number
PC28F640J3D75E
Description
IC FLASH 64MBIT 75NS 64EZBGA
Manufacturer
NUMONYX
Datasheet
1.PC28F640J3D75E.pdf
(68 pages)
Specifications of PC28F640J3D75E
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
64M (8Mx8, 4Mx16)
Speed
75ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
877116
877116
PC28F640J3D75 S L8ZT
877116
PC28F640J3D75 S L8ZT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC28F640J3D75E
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Numonyx™ Embedded Flash Memory (J3 v. D)
November 2007
308551-05
Blocks are selectively and individually lockable in-system. Individual block locking uses
block lock-bits to lock and unlock blocks. Block lock-bits gate block erase and program
operations. Lock-bit configuration operations set and clear lock-bits (using the Set
Block Lock-Bit and Clear Block Lock-Bits commands).
The Status Register indicates when the WSM’s block erase, program, or lock-bit
configuration operation is finished.
The STS (STATUS) output gives an additional indicator of WSM activity by providing
both a hardware signal of status (versus software polling) and status masking
(interrupt masking for background block erase, for example). Status indication using
STS minimizes both CPU overhead and system power consumption. When configured in
level mode (default mode), it acts as a RY/BY# signal. When low, STS indicates that the
WSM is performing a block erase, program, or lock-bit configuration. STS-high indicates
that the WSM is ready for a new command, block erase is suspended (and
programming is inactive), program is suspended, or the device is in reset/power-down
mode. Additionally, the configuration command allows the STS signal to be configured
to pulse on completion of programming and/or block erases.
Three CE signals are used to enable and disable the device. A unique CE logic design
reduces decoder logic typically required for multi-chip designs. External logic is not
required when designing a single chip, a dual chip, or a 4-chip miniature card or SIMM
module.
The BYTE# signal allows either x8 or x16 read/writes to the device:
Figure 1, “Memory Block Diagram (32, 64 and 128 Mbit)” on page 10
block diagram.
When the device is disabled, with CEx at VIH and RP# at VIH, the standby mode is
enabled. When RP# is at VIL, a further power-down mode is enabled which minimizes
power consumption and provides write protection during reset. A reset time (tPHQV) is
required from RP# going high until data outputs are valid. Likewise, the device has a
wake time (tPHWL) from RP#-high until writes to the CUI are recognized. With RP# at
VIL, the WSM is reset and the Status Register is cleared. (see
Truth Table” on page
• BYTE#-low enables 8-bit mode; address A0 selects between the low byte and high
• BYTE#-high enables16-bit operation; address A1 becomes the lowest order
byte.
address and address A0 is not used (don’t care).
31).
Table 15, “Chip Enable
shows a device
Datasheet
9