MC13892VK Freescale Semiconductor, MC13892VK Datasheet - Page 112

• Manufacturer Part Number: MC13892VK
• Description: IC PMU I.MX51/37/35/27 139MAPBGA
• Manufacturer: Freescale Semiconductor

Specifications of MC13892VK

• Applications: Battery Management, Display (LED Drivers), Handheld/Mobile Devices, Power Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: *
• Output Current: 65 mA
• Output Voltage: 1.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Voltage - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FUNCTIONAL DEVICE OPERATION
CONNECTIVITY
DETECTION COMPARATORS
to generate associated interrupts, and sense and masking bits are available through SPI (refer to
thresholds are specified for the minimum detect levels, and bits can be used in combination to qualify a VBUS window. Events
are communicated via (INT pin) interrupts and managed through SPI registers to allow the application processor to turn off the
PHY.
connector. The power input is then brought into an end product on the VBUS pin of the USB connector. For fault condition
robustness, VBUS over-voltage protection is included to protect the system and flag an over-voltage situation to the processor
via the USBOVI interrupt.
ID DETECTOR
on the application. However, it is also supports two additional modes which are outside of the USB standards: a factory mode
and a non-USB accessory mode. The state of the ID detection can be read via the SPI to poll dedicated sense bits for a floating,
grounded, or factory mode condition on the UID pin. There are also dedicated maskable interrupts for each UID condition as well.
set low it is a resistor. ID100KPU switches in an additional pull-up from VCORE to UID (independent of IDPUCNTRL). The UID
voltage can be read out via the ADC channel ADIN7, see
custom vendor applications by evaluation of the ADIN7 conversion reading.
Table 102. ID Detection Thresholds
112
Table 101. USB Detect Specifications
13892
Notes
76.
Resistor to Ground
Grounded
Floating
Voltage Applied
V
V
BVALID Comparator Threshold
BVALID Trip Delay
Over-voltage Protection Level
Over-voltage Protection Disconnect Time
VBUS detection and qualification is accomplished with two comparators, detailed in
As described in
The ID detector is primarily used to determine if a mini-A or mini-B style plug has been inserted into a mini-AB style receptacle
The ID detector is based on an on-chip pull-up controlled by the IDPUCNTRL bit. If set high the pull-up is a current source, if
The ID detector thresholds are listed in
UID Pin External
BUS
BUS
Connection
Valid Comparator trip level
Valid trip delay
UID maximum voltage is 5.25 V
Battery Interface and
Parameter
0.18 * VCORE < UID
< 0.77 * VCORE
0 < UID < 0.12 *
VCORE
0.89 * VCORE < UID
< VCORE
3.6V < UID
UID Pin Voltage
(76)
Control, the battery charger system is designed to work with the USB system physical
Table
IDFLOATS
102. Further interpretations of non-USB accessory detection may be made for
0
0
1
1
Including the USBI debounce
Rising trip delay
Falling trip delay
Rising and falling edge
Rising trip delay for turn on event
Falling trip delay for turn on event
Rising and falling edge
ADC
IDGNDS
1
0
1
1
Subsystem.
Condition
IDFACTORYS
0
0
0
1
Table
Non-USB accessory is attached (per CEA-
936-A spec)
A type plug (USB Default Slave) is
attached (per CEA-936-A spec)
B type plug (USB Host, OTG default
master or no device) is attached.
Factory mode
Analog Integrated Circuit Device Data
101. Comparator results are used
Min
4.4
8.0
4.0
8.0
5.6
20
20
-
-
SPI
Freescale Semiconductor
Accessory
Bitmap). Comparator
Typ
-
-
-
-
-
-
-
-
-
Max
4.65
4.4
6.0
1.0
24
12
40
12
-
Units
ms
ms
ms
μ
V
V
V
s