STLM75M2E STMicroelectronics, STLM75M2E Datasheet - Page 6

• Manufacturer Part Number: STLM75M2E
• Description: IC TEMP SENSOR DIGITAL SO-8
• Manufacturer: STMicroelectronics

Specifications of STLM75M2E

• Featured Product: STM32 Cortex-M3 Companion Products
• Function: Temp Sensor, Watchdog
• Topology: ADC (Sigma Delta), Comparator, Register Bank
• Sensor Type: Internal
• Sensing Temperature: -55°C ~ 125°C
• Output Type: I²C™/SMBus™
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Full Temp Accuracy: +/- 3 C
• Digital Output - Bus Interface: Serial (2-Wire, I2C)
• Digital Output - Number Of Bits: 9 bit
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 0.5°C
• Temperature Sensing Range: -55°C To +125°C
• Supply Current: 125µA
• Supply Voltage Range: 2.7V To 5.5V
• Sensor Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• For Use With: 497-10508 - BOARD EVAL FOR MEMS SENSORS497-10048 - BOARD EVAL ACCELEROMETER497-6238 - BOARD STLM75/STDS75/ST72F651
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Description
1
1.1
6/40
Description
The STLM75 is a high-precision digital CMOS temperature sensor IC with a sigma-delta
temperature-to-digital converter and an I
for general applications such as personal computers, system thermal management,
electronics equipment, and industrial controllers, and is packaged in the industry standard
8-lead TSSOP and SO8 packages.
The device contains a band gap temperature sensor and 9-bit ADC which monitor and
digitize the temperature to a resolution up to 0.5 °C. The STLM75 is typically accurate to
(±3 °C - max) over the full temperature measurement range of –55 °C to 125 °C with ±2 °C
accuracy in the –25 °C to +100 °C range. The STLM75 is pin-for-pin and software
compatible with the LM75B.
The STLM75 is specified for operating at supply voltages from 2.7 V to 5.5 V. Operating at
3.3 V, the supply current is typically (125 µA).
The on-board sigma-delta analog-to-digital converter (ADC) converts the measured
temperature to a digital value that is calibrated in degrees centigrade; for Fahrenheit
applications a lookup table or conversion routine is required.
The STLM75 is factory-calibrated and requires no external components to measure
temperature.
Serial communications
The STLM75 has a simple 2-wire I
user to access the data in the temperature register at any time. It communicates via the
serial interface with a master controller which operates at speeds up to 400 kHz. Three pins
(A0, A1, and A2) are available for address selection, and enable the user to connect up to 8
devices on the same bus without address conflict.
In addition, the serial interface gives the user easy access to all STLM75 registers to
customize operation of the device.
Doc ID 13296 Rev 12
2
C-compatible digital serial interface which allows the
2
C-compatible serial digital interface. It is targeted
STLM75