ISL54211EVAL1Z Intersil, ISL54211EVAL1Z Datasheet
ISL54211EVAL1Z
Specifications of ISL54211EVAL1Z
Related parts for ISL54211EVAL1Z
ISL54211EVAL1Z Summary of contents
Page 1
... CLICK L AND POP GND CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. All other trademarks mentioned are the property of their respective owners. ISL54211 FN6662 2.7V to 5.0V DD µ CONTROLLER ...
Page 2
... These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. ...
Page 3
... Maximum Junction Temperature (Plastic Package +150° 0.3V) Maximum Storage Temperature Range -65°C to +150°C DD Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . see link below ) + 0.3V) http://www.intersil.com/pbfree/Pb-FreeReflow.asp DD Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C or GND by specified amount are clamped. Limit current to maximum current DD Test Conditions: V ...
Page 4
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER ON-Resistance 3.3V 1.4V, CTRL = 40mA, V COMx (see Figure 3) r Matching Between V = 3.3V 1.4V, ...
Page 5
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER USB Switch -3dB Bandwidth Signal = 0dBm, 0.2VDC offset, R D+/D- OFF Capacitance 1MHz D+OFF D-OFF D+ COMx COM ON Capacitance ...
Page 6
Test Circuits and Waveforms V INH LOGIC 50% INPUT V INL t OFF SWITCH V INPUT INPUT V 90% SWITCH OUTPUT ogic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. ...
Page 7
Test Circuits and Waveforms CTRL AUDIO OR USB IMPEDANCE ANALYZER COMx GND Repeat test for all switches. FIGURE 4. CAPACITANCE TEST CIRCUIT t ri 90% 50% 10% DIN+ t skew_i DIN- 90% 50% 10 90% 10% ...
Page 8
Test Circuits and Waveforms AUDIO PRECISION SYSTEM II CASCADE R LOAD Set Audio Analyzer for Peak Detection, 32 Samples/Sec, Aweighted Filter, Manual Range 1X/Y, Units to dBV R LOAD Set Audio Analyzer for Peak Detection, 32 Samples/Sec, Aweighted Filter, Manual ...
Page 9
Typical Application Block Diagrams V BUS V 500kΩ BUS LOGIC CONTROL VIA V Detailed Description The ISL54211 device is a dual single pole/double throw (SPDT) analog switch that operates from a single DC power supply in the range of 2.7V ...
Page 10
USB differential data signals with minimal edge and phase distortion. The ISL54211 was specifically designed for MP3 players, personal media players and cellphone applications that need to combine the audio headphone jack and the USB data connector into a ...
Page 11
CTRL = Logic “0” (Low) when 0.5V or Floating. ≥ CTRL = Logic “1” (High) when 1.4V Audio Mode If the IN pin = Logic “0” and CTRL pin = Logic “1” the part will be in the Audio ...
Page 12
Audio or Mute mode, depending on the condition of the CTRL pin. Note: The ISL54211 contains an internal diode between the IN pin and VDD pin. Whenever the IN voltage is greater than the ...
Page 13
Typical Performance Curves 7 40mA COM 6.5 6.0 5 3.3V DD 5.0 V 4 3.5 3.0 0 0.1 0.2 V (V) COM FIGURE 14. USB ON-RESISTANCE vs SUPPLY VOLTAGE vs ...
Page 14
Typical Performance Curves FIGURE 20. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH 14 ISL54211 T = +25°C, Unless Otherwise Specified (Continued) A TIME SCALE (0.2ns/DIV) FN6662.1 August 25, 2008 ...
Page 15
Typical Performance Curves FIGURE 21. EYE PATTERN: 12Mbps USB SIGNAL WITH USB SWITCHES IN THE SIGNAL PATH - 3.3V DD -45 VSIGNAL = 0.707V RMS -50 - 10kΩ L -60 -65 -70 - 1kΩ ...
Page 16
Typical Performance Curves - - 50Ω LOAD -80 VSIGNAL = 0.707V RMS -90 -100 USB TO AUDIO -110 -120 -130 AUDIO TO USB -140 -150 -160 -170 -180 20 50 100 200 500 1k ...
Page 17
Typical Performance Curves V 1V/DIV 1. CTRL = 0V V 10mV/DIV OUT TIME (s) 200ms/DIV FIGURE 30. POWER-UP/POWER-DOWN CLICK AND POP TRANSIENT 17 ISL54211 T = +25°C, Unless Otherwise Specified (Continued) A ...
Page 18
... Dimensions D2 and E2 are for the exposed pads which provide M 0. improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions TERMINAL TIP MILLIMETERS MIN ...
Page 19
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...