LIS331DLMTR STMicroelectronics, LIS331DLMTR Datasheet - Page 17
![ACCELEROMETER MEMS 3AXIS 16-LGA](/photos/16/15/161591/lga16_sml.jpg)
LIS331DLMTR
Manufacturer Part Number
LIS331DLMTR
Description
ACCELEROMETER MEMS 3AXIS 16-LGA
Manufacturer
STMicroelectronics
Series
MEMS, nanor
Datasheet
1.STEVAL-MKI091V1.pdf
(38 pages)
Specifications of LIS331DLMTR
Featured Product
STM32 Cortex-M3 Companion Products
Axis
X, Y, Z
Acceleration Range
±2g, 4g, 8g
Sensitivity
64LSB/G, 32LSB/g, 16LSB/g
Voltage - Supply
2.16 V ~ 3.6 V
Output Type
Digital
Bandwidth
100Hz ~ 400Hz Selectable
Interface
I²C, SPI
Mounting Type
Surface Mount
Package / Case
16-LGA
Sensing Axis
X, Y, Z
Acceleration
2 g, 4 g, 8 g
Digital Output - Number Of Bits
8 bit
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.16 V
Supply Current
250 uA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Digital Output - Bus Interface
I2C, SPI
Mounting Style
SMD/SMT
Shutdown
Yes
For Use With
497-10048 - BOARD EVAL ACCELEROMETER
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LIS331DLMTR
Manufacturer:
STMicroelect
Quantity:
4 650
Part Number:
LIS331DLMTR
Manufacturer:
ST
Quantity:
20 000
LIS331DLM
5
5.1
Digital interfaces
The registers embedded inside the LIS331DLM may be accessed through both the I
SPI serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I
line must be tied high (i.e. connected to Vdd_IO).
Table 8.
I
The LIS331DLM I
content can also be read back.
The relevant I
Table 9.
There are two signals associated with the I
data line (SDA). The latter is a bidirectional line used for sending and receiving the data
to/from the interface. Both the lines are connected to Vdd_IO through a pull-up resistor
embedded inside the LIS331DLM. When the bus is free both the lines are high.
The I
normal mode.
2
C serial interface
Transmitter
2
Pin name
Receiver
C interface is compliant with fast mode (400 kHz) I
Master
Term
Slave
SDO
SDO
SPC
SDA
SCL
SA0
SDI
CS
Serial interface pin description
Serial interface pin description
2
C terminology is given in the table below.
2
C is a bus slave. The I
SPI enable
I
I
SPI serial port clock (SPC)
I
SPI serial data input (SDI)
3-wire interface serial data output (SDO)
I
SPI serial data output (SDO)
The device which sends data to the bus
The device which receives data from the bus
The device which initiates a transfer, generates clock signals and terminates a
transfer
The device addressed by the master
2
2
2
2
C/SPI mode selection (1: I
C serial clock (SCL)
C serial data (SDA)
C less significant bit of the device address (SA0)
Doc ID 15102 Rev 4
2
C is employed to write data into registers whose
2
C bus: the serial clock line (SCL) and the serial
2
C mode; 0: SPI enabled)
Pin description
Description
2
C standards as well as with the
Digital interfaces
2
C interface, CS
2
C and
17/38