011796 AP (SAK4/6) Weidmuller, 011796 AP (SAK4/6) Datasheet - Page 64

• Manufacturer Part Number: 011796 AP (SAK4/6)
• Description: END COVER, BUFF
• Manufacturer: Weidmuller
• Series: Wr

Specifications of 011796 AP (SAK4/6)

• Svhc: No SVHC (15-Dec-2010)
• Colour: Buff
• External Length / Height: 51.5mm
• Accessory Type: End / Intermediate Plate
• For Use With: W Series
• Lead Free Status / RoHS Status: na

Modular terminal blocks
for plug-in connectors
All types can be coded without reducing
the number of available connections. The
terminals can be used for up to 20 or 18.5
A. The WDK version saves significantly on
space as it not only takes up less room
along the mounting rail, but also across,
as two identical connectors can be plug-
ged in from the top.
Modular functional units form the key-ele-
ment for production systems constructed
according to the building-block principle.
Costly installation times can be reduced
significantly, and sub-units can be rapidly
replaced when maintenance or servicing is
carried out.
Terminal blocks using plug-in connectors
are tailor-made for this type of application.
They enable functional units to be repla-
ced rapidly, and the control system can be
supplemented or modified without any
problems.
WDU 2.5/BLZ
WDK 2.5/BLZ
2/52
plug-in connectors
pitch: 5.08 and 7.62 mm
rated voltage: 250 and 500 V
versions with LED’s
mounting brackets for firmly securing
for BLZ and BLA systems
ZKBD 2.5/1.5
ZKSD 2.5/1.5
The prime feature of the new ZKBD and
ZKSD terminal blocks for plug-in connec-
tors is their modular construction. This
system employs terminal block technology
where ZKBD and ZKSD form the base ter-
minals and ZSLD and ZBLD are the plug-
in connectors. The Weidmüller tension
clamp system is used to connect the con-
ductors. This system enables functional
units to be prefitted as well as tested with
test plugs. This applies equally to the reci-
procal component which could be a termi-
nal strip wired up to a machine, or in a lift,
tram or underground railway, etc.
tors for between 2 and 12 poles
ctor are each equipped with two
connections and two cross-connection
channels
number of poles
refore no break in the pitch and less
planning effort
modular construction; plug-in connec-
base terminal as well as plug-in conne-
coding system that does not reduce
resistant to shaking or vibrations
no end or partition plates required, the-
ZRV 1.5
On account of its low height of 55 mm
(plus space taken up by loop in cable), this
system can even be mounted inside very
flat enclosures. The width of only 5 mm
and the 4 through-connections reduce the
length of the terminal block assemblies
and make more space available inside the
control cabinet. Conductors are attached
on the terminal side by means of tension
clamp connections using a top-entry
system, and on the plug-in connector side
by crimped contacts. The ZRV 1.5 is avai-
lable as either a plain feedthrough terminal
or combined with a PE connection.
Reciprocally coded plugs, which cannot
be connected the wrong way round, are
available for both the plain feedthrough
terminal and the feedthrough terminal with
PE connection. It is also possible to fit
these plugs through PG 11 gland entries,
so that a PG threaded cable gland can be
attached to the cable in advance. As
cross-connections are possible within
each of the 4 levels, voltages can be distri-
buted systematically or even linked circuits
can be created.