ADF4252BCPZ Analog Devices Inc, ADF4252BCPZ Datasheet - Page 5

• Manufacturer Part Number: ADF4252BCPZ
• Description: IC, FREQUENCY SYNTHESIZER, 3GHZ LFCSP-24
• Manufacturer: Analog Devices Inc
• Type: Clock/Frequency Synthesizer (RF/IF), Fractional N, Integer Nr

Specifications of ADF4252BCPZ

• Pll Type: Frequency Synthesis
• Frequency: 3GHz
• Supply Current: 13mA
• Supply Voltage Range: 2.7V To 3.3V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 24
• Operating Temperature Range: -40°C To +85°C
• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 3:2
• Differential - Input:output: Yes/No
• Frequency - Max: 3GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 2.7 V ~ 3.3 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 3GHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4252EBZ2 - BOARD EVAL ADF4252 NO VCO/FILTER
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Mnemonic
CP
CP
RF
RF
A
MUXOUT
REF
REF
D
CLK
DATA
LE
R
A
IF
IF
DV
CP
CP
V
V
V
V
V
REV. B
GND
SET
GND
P
DD
DD
DD
P
GND
IN
IN
2
1
RF
GND
IN
IN
GND
IF
DD
B
A
2
3
1
IN
OUT
A
B
1
2
1
2
This multiplexer output allows either the RF or IF lock detect, the scaled RF or IF, or the scaled reference fre-
Serial Data Input. The serial data is loaded MSB first with the three LSBs being the control bits. This input is a
Function
RF Charge Pump Output. This is normally connected to a loop filter that drives the input to an external VCO.
RF Charge Pump Ground.
Input to the RF Prescaler. This small signal input is normally taken from the VCO.
Complementary Input to the RF Prescaler.
Analog Ground for the RF Synthesizer.
quency to be accessed externally.
Reference Input. This is a CMOS input with a nominal threshold of V
100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator.
Reference Output.
Digital Ground for the Fractional Interpolator.
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into the
shift register on the CLK rising edge. This input is a high impedance CMOS input.
high impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the
seven latches, the latch being selected using the control bits.
Connecting a resistor between this pin and ground sets the minimum charge pump output current. The relationship
between I
Therefore, with R
Ground for the IF Synthesizer.
Complementary Input to the IF Prescaler.
Input to the IF Prescaler. This small signal input is normally taken from the IF VCO.
Positive Power Supply for the Fractional Interpolator Section. Decoupling capacitors to the ground plane should
be placed as close as possible to this pin. DV
IF Charge Pump Ground.
IF Charge Pump Output. This is normally connected to a loop filter that drives the input to an external VCO.
IF Charge Pump Power Supply. Decoupling capacitors to the ground plane should be placed as close as possible
to this pin. This voltage should be greater than or equal to V
Positive Power Supply for the IF Section. Decoupling capacitors to the ground plane should be placed as close as
possible to this pin. V
Positive Power Supply for the RF Digital Section. Decoupling capacitors to the ground plane should be placed as close
as possible to this pin. V
Positive Power Supply for the RF Analog Section. Decoupling capacitors to the ground plane should be placed as close
as possible to this pin. V
RF Charge Pump Power Supply. Decoupling capacitors to the ground plane should be placed as close as possible
to this pin. This voltage should be greater than or equal to V
I
CP
min
=
1 6875
CP
R
.
SET
and R
SET
SET
= 2.7 kΩ, I
DD
is
DD
DD
2 has a value 3 V ± 10%. V
3 has a value 3 V ± 10%. V
1 has a value 3 V ± 10%. V
PIN FUNCTION DESCRIPTIONS
CPmin
= 0.625 mA.
DD
–5–
must have the same voltage as V
DD
DD
DD
2 must have the same voltage as V
3 must have the same voltage as V
1 must have the same voltage as V
DD
DD
2.
1.
DD
/2 and an equivalent input resistance of
DD
1, V
DD
DD
DD
DD
2, and V
1, V
2, V
1, V
DD
DD
DD
ADF4252
2, and DV
3, and DV
3, and DV
DD
3.
DD
DD
DD
.
.
.