DP83815DUJB National Semiconductor, DP83815DUJB Datasheet - Page 88
![IC, ENET CTRL 10BASET, 100MBPS, LBGA-160](/photos/19/0/190058/4551706_sml.jpg)
DP83815DUJB
Manufacturer Part Number
DP83815DUJB
Description
IC, ENET CTRL 10BASET, 100MBPS, LBGA-160
Manufacturer
National Semiconductor
Datasheet
1.DP83815DUJB.pdf
(108 pages)
Specifications of DP83815DUJB
Data Rate
100Mbps
Ethernet Type
10BASE-T
Supply Current
170mA
Supply Voltage Range
3V To 3.6V
Operating Temperature Range
0°C To +70°C
No. Of Pins
160
Termination Type
SMD
Filter Terminals
SMD
Rohs Compliant
No
Data Rate Max
100Mbps
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DP83815DUJB
Manufacturer:
NS
Quantity:
996
Company:
Part Number:
DP83815DUJB
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
DP83815DUJB
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
DP83815DUJB/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Subject to change without notice.
5.0 Buffer Management
5.3.2 Receive Data Flow
With a bus mastering architecture, some number of buffers
and descriptors for received packets must be pre-allocated
when the DP83815 is initialized. The number allocated will
directly affect the system's tolerance to interrupt latency.
The more buffers that you pre-allocate, the longer the
system will survive an incoming burst without losing
receive packets, if receive descriptor processing is delayed
or preempted. Buffers sizes should be allocated in 32 byte
multiples.
1. Prior to packet reception, receive buffers must be
2. The address of the first descriptor in this list is then
described in a receive descriptor list (or ring, if
preferred). In each descriptor, the driver assigns
ownership to the hardware by clearing the OWN bit.
Receive descriptors may describe a single buffer.
written to the RXDP register. As packets arrive, they
are placed in available buffers. A single packet may
occupy one or more receive descriptors, as required
by the application.The device reads in the first
descriptor into the RxDescCache.
rxDescRefr
XferDone
XferDone
rxAdvance
link = NULL
rxDescWrite
CR:RXE && CRDD
(Continued)
(descCnt == 0) && (rxPktBytes > 0)
Figure 5-7 Receive State Diagram
link != NULL
rxPktBytes == 0
rxIdle
88
If the receive buffer management state machine runs out of
descriptors while receiving a packet, data will buffer in the
receive FIFO. If the FIFO overflows, the driver will be
interrupted with an RxOVR error.
rxFifoBlock
3. As data arrives in the RxDataFIFO, the receive buffer
4. If end of packet was reached, the status in the
management state machine places the data in the
receive buffer described by the descriptor. This
continues until either the end of packet is reached, or
the descriptor byte count for this descriptor is
reached.
descriptor (in main memory) is updated by setting the
OWN bit and clearing the MORE bit, by updating the
receive status bits as indicated by the MAC, and by
updating the SIZE field. The status bits in cmdsts are
only valid in the last descriptor of a packet (with the
MORE bit clear). Also for the last descriptor of a
packet, the SIZE field will be updated to reflect the
actual amount of data written to the buffer (which
may be less the full buffer size allocated by the
descriptor).
XferDone && OWN
rxDescRead
CR:RXE && !CRDD
XferDone && !OWN
FifoReady
XferDone
Rev O
rxFragWrite
www.national.com