DSPIC30F3014-20I/PT Microchip Technology, DSPIC30F3014-20I/PT Datasheet - Page 105
![IC, DSC, 16BIT, 24KB 40MHZ, 5.5V, TQFP44](/photos/6/82/68251/c04-076_pt_sml.jpg)
DSPIC30F3014-20I/PT
Manufacturer Part Number
DSPIC30F3014-20I/PT
Description
IC, DSC, 16BIT, 24KB 40MHZ, 5.5V, TQFP44
Manufacturer
Microchip Technology
Series
DsPIC30Fr
Datasheets
1.DSPIC30F3014-30IPT.pdf
(228 pages)
2.DSPIC30F3014-30IPT.pdf
(16 pages)
3.DSPIC30F3014-30IPT.pdf
(6 pages)
4.DSPIC30F3014-30IPT.pdf
(14 pages)
5.DSPIC30F3014-30IPT.pdf
(20 pages)
6.DSPIC30F3014-20IP.pdf
(226 pages)
Specifications of DSPIC30F3014-20I/PT
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
30
Flash Memory Size
24KB
Supply Voltage Range
2.5V To 5.5V
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
30
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 13x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-TQFP, 44-VQFP
Package
44TQFP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
20 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
30
Interface Type
I2C/SPI/UART
On-chip Adc
13-chx12-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC30F006 - MODULE SKT FOR DSPIC30F 44TQFPAC164305 - MODULE SKT FOR PM3 44TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F301420IPT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F3014-20I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3014-20I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
16.2
16.2.1
The UART module is enabled by setting the UARTEN
bit in the UxMODE register (where x = 1 or 2). Once
enabled, the UxTX and UxRX pins are configured as an
output and an input, respectively, overriding the TRIS
and LAT register bit settings for the corresponding I/O
port pins. The UxTX pin is at logic ‘1’ when no
transmission is taking place.
16.2.2
The UART module is disabled by clearing the UARTEN
bit in the UxMODE register. This is the default state
after any Reset. If the UART is disabled, all I/O pins
operate as port pins under the control of the LAT and
TRIS bits of the corresponding port pins.
Disabling the UART module resets the buffers to empty
states. Any data characters in the buffers are lost and
the baud rate counter is reset.
All error and status flags associated with the UART
module are reset when the module is disabled. The
URXDA, OERR, FERR, PERR, UTXEN, UTXBRK and
UTXBF bits are cleared, whereas RIDLE and TRMT
are set. Other control bits, including ADDEN,
URXISEL<1:0>, UTXISEL, as well as the UxMODE
and UxBRG registers, are not affected.
Clearing the UARTEN bit while the UART is active
aborts all pending transmissions and receptions and
resets the module, as defined above. Re-enabling the
UART restarts the UART in the same configuration.
16.2.3
The alternate I/O function is enabled by setting the
ALTIO bit (UxMODE<10>). If ALTIO = 1, the UxATX
and UxARX pins (alternate transmit and alternate
receive pins, respectively) are used by the UART mod-
ule instead of the UxTX and UxRX pins. If ALTIO = 0,
the UxTX and UxRX pins are used by the UART
module.
16.2.4
Control bits, PDSEL<1:0> in the UxMODE register, are
used to select the data length and parity used in the
transmission. The data length may either be 8 bits with
even, odd or no parity, or 9 bits with no parity.
The STSEL bit determines whether one or two Stop bits
are used during data transmission.
The default (power-on) setting of the UART is 8 bits, no
parity and 1 Stop bit (typically represented as 8, N, 1).
© 2008 Microchip Technology Inc.
Enabling and Setting Up UART
ENABLING THE UART
DISABLING THE UART
ALTERNATE I/O
SETTING UP DATA, PARITY AND
STOP BIT SELECTIONS
16.3
16.3.1
The following steps must be performed in order to
transmit 8-bit data:
1.
2.
3.
4.
5.
16.3.2
The sequence of steps involved in the transmission of
9-bit data is similar to 8-bit transmission, except that a
16-bit data word (of which the upper 7 bits are always
clear) must be written to the UxTXREG register.
16.3.3
The transmit buffer is 9 bits wide and 4 characters
deep. Including the Transmit Shift register (UxTSR),
the user effectively has a 5-deep FIFO (First-In, First-
Out) buffer. The UTXBF status bit (UxSTA<9>)
indicates whether the transmit buffer is full.
If a user attempts to write to a full buffer, the new data
is not accepted into the FIFO, and no data shift occurs
within the buffer. This enables recovery from a buffer
overrun condition.
The FIFO is reset during any device Reset but is not
affected when the device enters or wakes up from a
power-saving mode.
dsPIC30F3014/4013
Set up the UART:
First, the data length, parity and number of Stop
bits must be selected. Then, the transmit and
receive interrupt enable and priority bits are set
up in the UxMODE and UxSTA registers. Also,
the appropriate baud rate value must be written
to the UxBRG register.
Enable the UART by setting the UARTEN bit
(UxMODE<15>).
Set the UTXEN bit (UxSTA<10>), thereby
enabling a transmission.
Write the byte to be transmitted to the lower byte
of UxTXREG. The value is transferred to the
Transmit Shift register (UxTSR) immediately,
and the serial bit stream starts shifting out during
the next rising edge of the baud clock. Alterna-
tively, the data byte can be written while UTXEN
= 0, following which, the user can set UTXEN.
This causes the serial bit stream to begin imme-
diately because the baud clock starts from a
cleared state.
A transmit interrupt is generated, depending on
the value of the interrupt control bit, UTXISEL
(UxSTA<15>).
Transmitting Data
TRANSMITTING IN 8-BIT DATA
MODE
TRANSMITTING IN 9-BIT DATA
MODE
TRANSMIT BUFFER (U
DS70138F-page 103
X
TXB)