BD3532EFV-E2 Rohm Semiconductor, BD3532EFV-E2 Datasheet
BD3532EFV-E2
Specifications of BD3532EFV-E2
Available stocks
Related parts for BD3532EFV-E2
BD3532EFV-E2 Summary of contents
Page 1
TECHNICAL NOTE High-performance Regulator IC Series for PCs Termination Regulators for DDR-SDRAMs BD3533F/FVM/EKN(1A),BD3531F(1.5A),BD3532F/EFV/KN(3A) Description BD3533/31/ termination regulator compatible with JEDEC DDR-SDRAM, which functions as a linear power supply incorporating an N-channel MOSFET and provides a sink/source current capability ...
Page 2
... VEN VTT_IN VDDQ ITT Pd1 560 * mW 3 Pd2 690 * mW -10～ Topr ℃ -55～ Tstg ℃ Tjmax +150 ℃ Symbol BD3532F BD3532EFV 1 VCC VEN VTT_IN VDDQ ITT Pd1 560 * - 3 1000 * Pd2 690 * Topr -40～+100 -40～+100 Tstg -55～+150 -55～+150 ...
Page 3
OPERATING CONDITIONS ◎BD3533F/FVM/EKN(Ta=25℃) Parameter Input Voltage Termination Input Voltage VDDQ Reference Voltage Enable Input Voltage ◎BD3531F(Ta=25℃) Parameter Input Voltage Termination Input Voltage EN Input Voltage ◎BD3532F/EFV/KN(Ta=25℃) Parameter Input Voltage Termination Input Voltage EN Input Voltage ★ No radiation-resistant design ...
Page 4
CHARACTERISTICS ◎BD3533F/FVM/EKN ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=3.3V VEN=3V VDDQ=1.8V VTT_IN=1.8V) Parameter [Input of Reference Voltage] Input Impedance ZVDDQ Output Voltage1 Output Voltage2 Output Voltage3 Output Voltage4 [Reference voltage] Source Current Sink Current [UVLO] UVLO OFF Voltage Hysteresis Voltage ...
Page 5
ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=5V VEN=3V VDDQ=2.5V VTT_IN=2.5V) Parameter Symbol Standby Current IST Bias Current ICC [Enable] Hi Level Enable Input VENHI Voltage Low Level Enable Input VENLOW Voltage Enable Pin Input Current IEN [Termination] Termination Output Voltage ...
Page 6
Data VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.1 DDRⅠ(-1A→1A) BD3531 VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.4 DDRⅠ(1A→-1A) BD3531 VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.7 DDRⅡ(-1A→1A) BD3531 VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.10 DDRⅡ(1A→-1A) BD3531 VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.2 DDRⅠ(-1A→1A) BD3532 VTT(10mV/Div) ITT(1A/Div) 10μsec/Div Fig.5 DDRⅠ(1A→-1A) BD3532 VTT(10mV/Div) ITT(1A/Div) ...
Page 7
IREF(mA) Fig.13 IREF-VREF (DDR-Ⅰ) 0.91 0.912 0.91 0.910 0.90 0.908 0.90 0.906 0.90 0.904 0.90 0.902 0.90 0.900 0.89 0.898 0.896 0. ITT(A) Fig.16 ITT-VTT ...
Page 8
DIAGRAM ◎BD3533F/FVM/EKN VCC VCC Reference Block Thermal Protection Enable EN EN ◎BD3531F VCC VCC Reference Block Thermal Protection Enable EN ◎BD3532F/FVM/EKN VCC VCC Reference Block Thermal Protection Enable EN EN VDDQ VTT_IN VDDQ VCC VCC VCC UVLO SOFT TSD ...
Page 9
CONFIGRATION GND VTTS 3 4 VREF ◎BD3532KN ●PIN CONFIGRATION VTT_IN2 NC VTT_IN1 VTT1 VTT2 PGND1 SGND NC EN PGND2 ◎BD3533EKN ●PIN CONFIGRATION VTT VTT_IN VTT_IN VCC NC 15 ...
Page 10
... CONFIGRATION VTT1 VTT2 PGND1 PGND2 SGND EN VTTS NC VREF VREFS ●Description of operations ・VCC In BD3533/31/32, an independent power input pin is provided for an internal circuit operation of the IC. This is used to drive the amplifier circuit of the IC, and its maximum current rating is 4 mA. The power supply voltage is 3.3 to 5.5 volts (BD3533 volts (BD3531/32 recommended to connect a bypass capacitor of 1 μ ...
Page 11
A DDR memory termination output pin. respectively. The output voltage tracks the voltage divided in half at VDDQ pin. VTT output is turned to OFF when VCC UVLO or thermal shutdown protector is activated with EN pin level turned ...
Page 12
Heat loss Thermal design must be conducted with the operation under the conditions listed below (which are the guaranteed temperature range requiring consideration on appropriate margins etc.): 1. Ambient temperature Ta: 100°C or lower 2. Chip junction temperature Tj: ...
Page 13
GND wiring pattern When both a small-signal GND and high current GND are present, single-point grounding (at the set standard point) is recommended, in order to separate the small-signal and high current patterns, and to be sure the voltage ...
Page 14
... Ambient Temperature [Ta] (1) 70mm×70mm×1.6mm Glass-epoxy PCB θj-c=181℃/W (2) With no heat sink θj-a=222℃/W ◎HTSSOP-B20(BD3532EFV) 5 PCB①：θja=125.0℃/W 4 PCB②：θja=86.2℃/W ④3.20W PCB③：θja=54.3℃/W 3 PCB④：θja=39.1℃/W ③ ...
Page 15
Part Number Package Type ・BD3533 ・F : SOP8 ・BD3531 ・FVM : MSOP8 ・BD3532 ・HFV : HTSSOP-B20 ・KN : VQFN28 ・EKN : HQFN20V SOP8 <Dimension> 5.0±0 0.15±0.1 0.1 1.27 0.4±0.1 MSOP8 ...
Page 16
VQFN28 <Dimension> 5.2±0.1 5.0±0.1 (1. 0.5 7 0.22±0.05 0.05 + 0.1 (0.6 ) − 0.3 0.05 (Unit:mm) HQFN20V <Dimension> (2.1) 4.2 ± 0.1 4.0 ± 0.1 0.5 (1. ...
Page 17
Appendix No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM CO.,LTD. The content specified herein is subject to change for improvement without notice. The content specified herein is for the ...