ISL6414IR-TK Intersil, ISL6414IR-TK Datasheet
ISL6414IR-TK
Specifications of ISL6414IR-TK
Available stocks
Related parts for ISL6414IR-TK
ISL6414IR-TK Summary of contents
Page 1
... Ordering Information TEMP. PART NUMBER RANGE (°C) PACKAGE ISL6414IR - QFN ISL6414IR-T5K 16 Ld QFN Tape and Reel ISL6414IR- QFN Tape and Reel ISL6414IRZ (Note) - QFN (Pb-free) ISL6414IRZ- QFN Tape and Reel (Note) (Pb-free) NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets ...
Page 2
Pinout ISL6414 (QFN) TOP VIEW RESET CT 2 SHDN 3 SHDN3 Typical Application Schematic +3. 3.3µF C7 0.01µF +2.84V V OUT3 C5 3.3µF 2 ISL6414 12 OUT1 ...
Page 3
Functional Block Diagram VIN 15 FAULT VIN 3 SHDN 4 SHDN3 RESET 1 RESET 8 GND 3 ISL6414 Gm BAND GAP WINDOW REF. COMP 1.2V Gm THERMAL SHUT DOWN 150°C Gm CONTROL LOGIC ENABLES RESET POR POR ...
Page 4
Absolute Maximum Ratings (Note SHDN/SHDN3 to GND/GND3 . . . . . . . . . . . . . . . -7.0V to 7.0V IN SET, CC, FAULT to GND/GND3 . . . . . . ...
Page 5
Electrical Specifications V = +3.3V, Compensation Capacitor = 33nF PARAMETER Output Voltage Noise LDO3 SPECIFICATIONS Output Voltage (V ) OUT3 Output Voltage Accuracy Maximum Output Current (I ) (Note 6) OUT3 Output Current Limit (Note 6) Dropout Voltage ...
Page 6
Typical Performance Curves TIME (1ms/DIV) FIGURE 3. LINE TRANSIENT RESPONSE ( TIME (1ms/DIV) FIGURE 5. LINE TRANSIENT RESPONSE ( 100 0 TIME (2ms/DIV) FIGURE 7. LOAD TRANSIENT RESPONSE (V ...
Page 7
Typical Performance Curves 1.2 1.1 1 0.9 0.8 -40 - TEMPERATURE (°C) FIGURE 9. LD01 LOAD REGULATION vs TEMPERATURE 1.4 1.3 1.2 1.1 1 0.9 0.8 -40 - TEMPERATURE (°C) FIGURE 11. LD03 LOAD REGULATION vs ...
Page 8
Typical Performance Curves 8.3 8.25 8.2 8.15 8.1 8.05 8 -40 - TEMPERATURE (°C) FIGURE 15. SHUTDOWN CURRENT vs TEMPERATURE 180 160 140 120 100 -40 - TEMPERATURE (°C) FIGURE 17. ...
Page 9
Pin Descriptions OUT1 - This pin is the output for LDO1. Bypass with a minimum of 2.2µF, low ESR capacitor to GND for stable operation Supply input pins. Connect to input power source. IN Bypass with 2.2µF capacitor ...
Page 10
Output Voltages The ISL6414 provides fixed output voltages for use in Wireless Chipset applications. Internal trimmed resistor networks set the typical output voltages as shown here 1.8V 2.84V; V OUT1 OUT2 OUT3 Shutdown Driving the SHDN ...
Page 11
For stable operation, a ceramic capacitor whose value is minimum 3.3µF is recommended for V 300mA output current and 2.2µF is recommended for V and V each at 200mA load ...
Page 12
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...