LM4781TA National Semiconductor, LM4781TA Datasheet - Page 20

• Manufacturer Part Number: LM4781TA
• Description: Audio Power Amplifier IC
• Manufacturer: National Semiconductor

Specifications of LM4781TA

• Amplifier Case Style: TO-220
• Peak Reflow Compatible (260 C): No
• Termination Type: Through Hole
• Supply Voltage Max: 56V
• Leaded Process Compatible: No
• Package / Case: 27-TO-220
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 3-Channel Stereo
• Output Power (typ): 35x3@8OhmW
• Audio Amplifier Function: Speaker
• Input Offset Voltage: 10@±28VmV
• Input Bias Current: 1uA
• Total Harmonic Distortion: 0.2@8Ohm@20W%
• Single Supply Voltage (typ): 18V
• Dual Supply Voltage (typ): ±12/±15/±18/±24/±28V
• Power Supply Requirement: Single/Dual
• Power Dissipation: 125W
• Unity Gain Bandwidth Product (typ): 8MHz
• Rail/rail I/o Type: No
• Power Supply Rejection Ratio: 125dB
• Single Supply Voltage (min): 20V
• Single Supply Voltage (max): 70V
• Dual Supply Voltage (min): ±10V
• Dual Supply Voltage (max): ±35V
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 27 +Tab
• Package Type: TO-220
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

www.national.com
Application Information
LAYOUT, GROUND LOOPS AND STABILITY
The LM4781 is designed to be stable when operated at a
closed-loop gain of 10 or greater, but as with any other
high-current amplifier, the LM4781 can be made to oscillate
under certain conditions. These oscillations usually involve
printed circuit board layout or output/input coupling issues.
When designing a layout, it is important to return the load
ground, the output compensation ground, and the low level
(feedback and input) grounds to the circuit board common
ground point through separate paths. Otherwise, large cur-
rents flowing along a ground conductor will generate volt-
ages on the conductor which can effectively act as signals at
the input, resulting in high frequency oscillation or excessive
distortion. It is advisable to keep the output compensation
components and the 0.1µF supply decoupling capacitors as
close as possible to the LM4781 to reduce the effects of PCB
trace resistance and inductance. For the same reason, the
ground return paths should be as short as possible.
In general, with fast, high-current circuitry, all sorts of prob-
lems can arise from improper grounding which again can be
avoided by returning all grounds separately to a common
point. Without isolating the ground signals and returning the
grounds to a common point, ground loops may occur.
“Ground Loop” is the term used to describe situations occur-
ring in ground systems where a difference in potential exists
between two ground points. Ideally a ground is a ground, but
unfortunately, in order for this to be true, ground conductors
with zero resistance are necessary. Since real world ground
leads possess finite resistance, currents running through
them will cause finite voltage drops to exist. If two ground
return lines tie into the same path at different points there will
be a voltage drop between them. The first figure below
shows a common ground example where the positive input
ground and the load ground are returned to the supply
ground point via the same wire. The addition of the finite wire
resistance, R
two points as shown below.
2
, results in a voltage difference between the
(Continued)
20067398
20
The load current I
I
Therefore the voltage appearing at the non-inverting input is
effectively positive feedback and the circuit may oscillate. If
there was only one device to worry about then the values of
R
however, several devices normally comprise a total system.
Any ground return of a separate device, whose output is in
phase, can feedback in a similar manner and cause insta-
bilities. Out of phase ground loops also are troublesome,
causing unexpected gain and phase errors.
The solution to most ground loop problems is to always use
a single-point ground system, although this is sometimes
impractical. The third figure above is an example of a single-
point ground system.
The single-point ground concept should be applied rigor-
ously to all components and all circuits when possible. Vio-
lations of single-point grounding are most common among
printed circuit board designs, since the circuit is surrounded
by large ground areas which invite the temptation to run a
device to the closest ground spot. As a final rule, make all
ground returns low resistance and low inductance by using
large wire and wide traces.
Occasionally, current in the output leads (which function as
antennas) can be coupled through the air to the amplifier
input, resulting in high-frequency oscillation. This normally
happens when the source impedance is high or the input
leads are long. The problem can be eliminated by placing a
small capacitor, C
the LM4781 input terminals. Refer to the External Compo-
nents Description section relating to component interaction
with C
REACTIVE LOADING
It is hard for most power amplifiers to drive highly capacitive
loads very effectively and normally results in oscillations or
ringing on the square wave response. If the output of the
LM4781 is connected directly to a capacitor with no series
resistance, the square wave response will exhibit ringing if
the capacitance is greater than about 0.2µF. If highly capaci-
tive loads are expected due to long speaker cables, a
method commonly employed to protect amplifiers from low
impedances at high frequencies is to couple to the load
through a 10Ω resistor in parallel with a 0.7µH inductor. The
inductor-resistor combination as shown in the Figure 5 iso-
lates the feedback amplifier from the load by providing high
output impedance at high frequencies thus allowing the 10Ω
resistor to decouple the capacitive load and reduce the Q of
the series resonant circuit. The LR combination also pro-
vides low output impedance at low frequencies thus shorting
out the 10Ω resistor and allowing the amplifier to drive the
series RC load (large capacitive load due to long speaker
cables) directly.
INVERTING AMPLIFIER APPLICATION
The inverting amplifier configuration may be used instead of
the more common non-inverting amplifier configuration
shown in Figure 1. The inverting amplifier can have better
THD+N performance and eliminates the need for a large
capacitor (Ci) reducing cost and space requirements. The
values show in Figure 6 are only one example of an amplifier
with a gain of 20V/V (Gain = -R
values, the value of R
combination of R
I
, thus V
1
and R
f
.
1
2
will follow the output voltage directly, i.e. in phase.
would probably be small enough to be ignored;
f
L
C
and Ri.
will be much larger than input bias current
, (on the order of 50pF to 500pF) across
B
should be eqaul to the parallel
f
/R
i
). For different resistor