PIC16C781-I/SO Microchip Technology, PIC16C781-I/SO Datasheet - Page 85

• Manufacturer Part Number: PIC16C781-I/SO
• Description: 1.75 KB OTP, 128 RAM, 16 I/O 20 SOIC .300in TUBE
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C781-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 1.75KB (1K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b; D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGAC164028 - MODULE SKT PROMATEII 20SOIC/DIP
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC16C781I/SO

11.0
The Operational Amplifier (OPA) Module can be config-
ured as either an OPAMP or Voltage Comparator. The
OPA module has the following features:
• External connections to all ports
• Gain Bandwidth Product selectable:
• Low leakage inputs
• Input Offset Voltage Automatic Calibration Module
• Input Offset Voltage calibration at a programma-
• Interrupt-on-change in Comparator mode using
11.1
The OPACON register, shown in Register 11-1, controls
the OPA module. The CALCON register, shown in
Register 11-2, controls the Automatic Calibration Module.
FIGURE 11-1:
- 70 kHz nom.
- 2 MHz nom.
(ACM)
ble common mode voltage using the DAC
IOCB
2001 Microchip Technology Inc.
OPERATIONAL AMPLIFIER
(OPA) MODULE
Control Registers
OPA MODULE BLOCK DIAGRAM
RA0/AN0/OPA+
RA1/AN1/OPA-
RB3/AN7/OPA
Preliminary
OPA
11.1.1
The OPA module is enabled by setting the OPAON bit
(OPACON<7>). When enabled, the OPA forces the
output driver of RB3/AN7/OPA into tri-state to prevent
contention between the driver and the OPA output.
Clearing the CMPEN bit (OPACON,6>) configures the
module as an OPAMP. Setting CMPEN configures the
module as a voltage comparator.
The GBWP bit (OPACON<0>) controls the speed of the
module in both comparator and OPAMP configurations.
Setting GBWP results in a Gain Bandwidth Product
(GBWP) of 2 MHz typical. Clearing GBWP0 results in a
GBWP of the OPA of 70 kHz typical.
Note 1: When the OPA module is enabled, the
OPAON
CMPEN
GBWP
2: In Comparator mode (CMPEN = 1), an
TO ADC MUX
OPACON REGISTER
RB3/AN7/OPA pin is driven by the
OPAMP output, not by the PORTB driver.
Refer to the Electrical specifications for
the OPAMP output drive capability.
interrupt can be generated using the
IOCB feature of RB3. RB3 must be pro-
grammed as a digital input with IOCB
enabled.
PIC16C781/782
DS41171A-page 83