PIC16F916T-I/SS Microchip Technology, PIC16F916T-I/SS Datasheet - Page 34

• Manufacturer Part Number: PIC16F916T-I/SS
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F916T-I/SS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 352 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA160011 - DAUGHTER BOARD PICDEM LCD 16F91X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F913/914/916/917/946
2.2.2.1
The STATUS register, shown in Register 2-1, contains:
• the arithmetic status of the ALU
• the Reset status
• the bank select bits for data memory (SRAM)
The STATUS register can be the destination for any
instruction, like any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
REGISTER 2-1:
DS41250F-page 32
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6-5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R/W-0
IRP
For Borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the
second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order
bit of the source register.
STATUS Register
IRP: Register Bank Select bit (used for indirect addressing)
1 = Bank 2, 3 (100h-1FFh)
0 = Bank 0, 1 (00h-FFh)
RP<1:0>: Register Bank Select bits (used for direct addressing)
00 = Bank 0 (00h-7Fh)
01 = Bank 1 (80h-FFh)
10 = Bank 2 (100h-17Fh)
11 = Bank 3 (180h-1FFh)
TO: Time-out bit
1 = After power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit Carry/Borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
C: Carry/Borrow bit
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
R/W-0
RP1
STATUS: STATUS REGISTER
W = Writable bit
‘1’ = Bit is set
R/W-0
RP0
(1)
(ADDWF, ADDLW, SUBLW, SUBWF instructions)
R-1
TO
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register, because these instructions do not
affect any Status bits. For other instructions not
affecting
“Instruction Set Summary”).
R-1
PD
Note 1: The C and DC bits operate as Borrow and
any
Digit Borrow out bits, respectively, in
subtraction.
R/W-x
Z
Status
(1)
© 2007 Microchip Technology Inc.
(1)
x = Bit is unknown
bits
R/W-x
DC
(1)
(see
Section 17.0
R/W-x
C
(1)
bit 0