NC2D JP 12VDC PANASONIC EW, NC2D JP 12VDC Datasheet
NC2D JP 12VDC
Specifications of NC2D JP 12VDC
Related parts for NC2D JP 12VDC
NC2D JP 12VDC Summary of contents
Page 1
... High contact reliability due to bifurcated contacts 10.9 — 2C 250 V AC, 4C 125 V AC 250 V AC .429 • Latching types available • Low operating power — 2C: 200 mW, 4C: 400 mW (Single side stable) 2C Flat type • Soldering flux inflow prevented by terminal location 11.2 • ...
Page 2
... NC TYPICAL APPLICATIONS Use NC Relays for power control — Tape recorders, temperature controls, video tape recorders Telecommunications equipment, measuring controls, copiers ORDERING INFORMATION Ex. NC Contact arrangement Type classification 2: 2 Form C Nil: Standard type 4: 4 Form C EB: Amber sealed type (Notes) 1. Flat series are available in PC board terminal types only. ...
Page 3
... NC4D-JPL2-DC110V NC4D-L2-DC110V Notes: 1. Two coil latching relay 4C series are for intermittent operation only. Power should be applied to coil continuously for no more than two minutes. 2. Coil resistance is the measured value at a coil temperature of 20°C. Compensate coil resistance by plus or minus 0.4% for each degree (°C) of coil temperature change ...
Page 4
NC 4C single side stable (NC4D-JP) Standard type 5.08 5.08 5.08 5.08 5.08 5.08 .200 .200 .200 .200 .200 .200 (NC4EBD-JP) 38.1 1.500 5.08 7.62 5.08 7.62 .200 .300 .200 .300 4C 2 coil latching (NC4D-JPL2) Standard type 5.08 5.08 ...
Page 5
Standard type (NC2EBD-P) 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 7.62 5.08 5.08 .300 .200 2.54 .100 4C single side stable (NC4D-P) Standard type (NC4EBD-P) 38.1 ...
Page 6
NC Slim series Plug-in series 2C single side stable Standard type (NC2D) (NC2EBD) 25.4 1.000 5.08 5.08 5.08 .200 .200 .200 7.62 5.08 7.62 .300 .200 .300 2C 2 coil latching ...
Page 7
... Same operation as conventional magnetic relays. Contacts will transfer only when coil is energized under indicated polarity coil latching Contacts will transfer only when coil is energized under indicated polarity. Once transferred, contacts remain in that position even with power off until opposite coil is energized at indicated polarity Reset set Diagrams show the “ ...
Page 8
NC 3. Operate time for single side stable Max. Max. 6 Min. 4 Min 100 110 Coil applied voltage,%V 5. Rate of change of pick-up and drop-out voltage ...
Page 9
... Flat series 250 V AC Slim series 250 V AC Initial breakdown voltage 2,000 V AC (Except for coil-coil of L2 types: 1,500 V AC) Initial insulation resistance Heat resistance Caution: Do not insert or remove relays while in the energized condition. en_ds_61135_0000: 310105J NC4 Flat NC2 Slim screws necessary. Relays are held firmly in the socket by clips integrally molded into the socket ...
Page 10
NC DIMENSIONS Flat series NC2-JPS Terminal width: 0.9 Terminal thickness: 0.4 NC2-JPL2S 2-3.5 DIA. HOLES 2-.138 DIA. HOLES 10.16 .400 25.4 1.000 Terminals 3 and 6 excluded for NC2-JPS. NC4-JPS Terminal width: 0.9 Terminal thickness: 0.4 NC4-JPL2S 2-3.5 DIA. HOLES ...
Page 11
... Reset coil 4 3 Set switch Reset switch 2. 2 coil latching series 4C are for intermittent operation only. Power should be applied to coils continuously for no more than two minutes. 3. When designing printed circuit board patterns, note that: (1) “Top View” wiring diagram is indicated for the Flat series because terminals can be seen from above ...