S-8130AACFN-MAET2G Seiko Instruments, S-8130AACFN-MAET2G Datasheet
S-8130AACFN-MAET2G
Specifications of S-8130AACFN-MAET2G
Related parts for S-8130AACFN-MAET2G
S-8130AACFN-MAET2G Summary of contents
Page 1
... The S-8130AA consists of a temperature sensor having the temperature coefficient of −13 mV/°C, a reference voltage source, a comparator, voltage detection circuit, and noise suppression circuit all of which are enclosed in 8-Pin MSOP package. Since the temperature range of this IC is −40 to +100 ° possible to achieve the extensive application for temperature control. Features • ...
Page 2
... TEMPERATURE SWITCH IC WITH LATCH S-8130AA Series Block diagram S-8130AAxFN-xxxT2z (Fixed detection temperature) VDD Temparature Sensor Vref RESET Voltage detector with delay circuit CD2 VSS Figure 1 Seiko Instruments Inc. Rev.3.0 VOUT RT Vref Reference voltage source CD1 Q DET D D-F _00 ...
Page 3
... Rev.3.0 _00 Product Name Structure 1. Product name S - 8130 Option list • Detection temperature T DET • DET output is selectable active high or active low. • Release voltage V is selectable in 0.1 V step in the range between 2.2 and 3.4 V. RET • RESET pin is selectable “PuII-up” or “Nch Open Drain”. ...
Page 4
... Positive power supply pin 2 DET Output pin for detection at the defined temperature 3 CD2 Capacitor connection pin for delay time setting in voltage detection 4 CD1 Capacitor connection pin for time setting of malfunction prevention 5 VSS Ground pin 6 Input/Output pin for reset RESET Active low 7 RT ...
Page 5
... Board size : (2) Board name : JEDEC STANDARD51-7 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Recommended values for external parts ...
Page 6
... Ta V detector Operating current Electrical Characteristics Parameters Symbol Noise filtering time T noise Delay time for T delay voltage detector Definition of the symbols used in the voltage detection circuit Hysteresis width (V ) HYS 6 Table 5 (Ta=25°C, V Conditions ⎯ ⎯ =2 DET Applied ...
Page 7
... Delay coefficient (25°C): Min. 4.3, Typ. 6.4, Max. 8.5 • Layout the board wiring so that the current does not flow into or flow out of the CD2 pin to have correct delay time since the impedance of the CD2 pin is high. • Capacitance of the external capacitor C compared to the internal constant current ...
Page 8
... Since the S-8130AA has a voltage detector inside, control for the RESET pin is not necessary to activate the circuit as seen in Figure this case the RESET pin should be open. (2) A capacitor of around 1 μ F should be connected to the DET pin to prevent malfunction caused by a noise due to the power on. ...
Page 9
... Rev.3.0 _00 Typical Characteristics 1. Current consumption vs. power voltage I DD 14.0 13.0 25°C 12.0 11 DET pin I vs. V characteristics SOURCE DD − SOU RCE -40° 25° ( DET pin I vs. V characteristics SINK DD − SIN -40°C 20 25° (V) DD TEMPERATURE SWITCH IC WITH LATCH − 100° -40° ...
Page 10
...
Page 11
...
Page 12
...
Page 13
... Seiko Instruments Inc. is strictly prohibited. • The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. ...